Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
I note with interest that Nordic is providing support (e.g., downloads) to run CircuitPython 10.1.4 on various Nordic devices, including the nRF54H20-DK . I've just received...
Hi I am able to load the nrf9151dk_at_client example hex on my custom dev board . I try accessing the AT commands and I can very easily get the responses. I want to install...
I'm using nRF52832 SoC with nRF5_SDK17.1.0 and SoftDevice v7.3.0. I'm using following code to write data into flash.
err_code = nrf_fstorage_write(&g_fs, write_addr, buffer32...
HI，
I am currently conducting secondary development based on the periodic_adv_conn sample in the ncs 3.2.1 SDK . Now I want to add continuous carrier wave output and continuous...
I work on nrf connect sdk v3.2.4(nRF54L15).
I plan to run the main application on cpuapp and the device control application on FLPR. It's currently working fine. In the...
I'm currently testing an app, which was running with a nrf9160/mfw-1.3.7/NCS 2.9.2.
Running this app now with nrf9151/mfw-2.0.4/NCS 3.1.0 seems to get a smaller response...
Hello,
I previously opened a ticket describing an issue where using MCUBoot in NCS v3.1.0 caused the GRTC to reset after a sys_poweroff() .
As discussed in that ticket...
Hi,
I am working on the XIAO BLE SENSE board which has nRF52840 SOC with P25Q16h 2MB flash and other sensors
I want to access the external flash to store sensor data....
Hi Nordic Team,
I am currently developing applications for custom boards using the nRF Connect SDK v2.6.0, focusing on the nRF52840 microcontroller.
In our ongoing project...
Hello,
I am using the nRF54L15-DK development board running the official hci_uart example as the BLE controller. My own Linux system acts as the host using BlueZ to control...
Hi Nordic team,
I noticed that when using the external FEM (nRF21540) with the nRF54L5 device, the power consumption at a transmit power setting of 8 dBm is significantly...
Hi, I have implemented a soft UART in the VPR FLPR. I am having trouble power managing it. I see an unexplained extra 500 uA current draw after I start the CPR until I reset...
Hi, for nRF52840 raw proprietary RADIO mode, do TXADDRESS and RXADDRESSES imply a hard total node-count limit for a custom multi-node network, or only a simultaneous hardware...
SDK is NCS2.9.2,My device supports master-slave integration. As a slave, it can pair and bind with a mobile phone. As a master, it can scan and connect to two slave devices...
