Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hello,
I'm trying to interface nRF52832 with an AFE IC which has to dialogue with nRF via SPI. Since this IC requires an external clock source, and Here is said that this...
Dear ,
I am new to the Nordic platform and started using VScode to build up and test some examples from the SDK.
I was using an nRF52840 dongle and trying to replicate...
Hi.
I'm enabling a BLE sniffer on rRF52840 DK to listen to packets between Windows and the other one BLE board, I can get advertising packets but Wireshark can't switch...
Our mission is prevention the increasing cases of missing persons. We wish to design a positioning device which can track the location of our users for their safety.
...
How we can get to know about the ADC sampling is done. On the basis of the sampling done i want to do furture opration like the stop sampling,Continues sampling. How i can...
Dear Experts,
I am planing to use 52810 to connect to a BLE speaker to play a short 'music'. I checked the BLE services provided in SDK:nRF5_SDK_17.0.2... but seems none...
Hi
I'm developing nRF52832.
I have a question about SPI communication.(\nRF5_SDK_17.0.0\examples\peripheral\spi I don't understand, so I ask questions.)
I want to read...
We plan to use nRF52840 in our new project. But the application is likely to be larger than 500 Kbytes
So we are going to use the only one Bank flash for DFU as in following...
We are thinking of making changes to the QIAA aQFN73 circuit configuration from 5 to 4 and use the REG0 DC/DC. VDDH will be connected to a single-cell Li-Ion battery (3~4...
hi, i am working with nrf52840 and need a stand alone qspi peripheral in the project. what is the straight forward way to get qspi into the code up and running without involving...
Håkon Alseth was helping me with this: https://devzone.nordicsemi.com/f/nordic-q-a/83126/hard-fault-using-twi_scanner-example I accidentally clicked "verify answer" when trying...
Hi,
I have the Power Profiler Kit PCA63511 used on top of the dev kit PCA10040. I am trying to measure the power consumption of my custom hardware implementing nrf52832...
Hello,
I am using nrf52840, SDK 17.0.2, softdevice s140 and also implemented OTA DFU in my application.
I want to save some data lets say admin code in flash. Once I burn...
Hello,
I'm having difficulty getting the GPIO set up in a way that behaves predictably on the nRF9160 DK. As far as I understand it, the nRF52840 is what controls the GPIO...
