Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I am trying to build the zephyr blink project using west :
I have installed the gnu-arm-embedded toolchain and set my environment variables accordingly : ZEPHYR_TOOLCHAIN_VARIANT...
Hello
The Uart Baudrate is initiliazed at 115200 baud but i the BLE nRF52833 is sending with about 115900.
I try to switch to hf clock but the baudrate is to high.
...
Hey,
I have a nRF central that connects and bonds to peripheral devices via BLE.
From what I understand, the peripheral device has a BLE MAC address that isn't consistent...
I am setting to NRF_SDH_BLE_CENTRAL_LINK_COUNT=1 ,it is working fine for ( 1 central and 1 peripheral )connection is fine(data also sending),but i am changed to NRF_SDH_BLE_CENTRAL_LINK_COUNT...
Hi
I am new to Nordic
I am using nordic nrf52832 with segger embedded software tool woth nordic support version NRF SDK 16.0.0
I am facing issue with build configutations...
Hello.
I would like to get an event that an advertised packet has been sent in a peripheral device. Is there a way to do this? Also, is it possible to get the channel used...
I'm using nRF9160DK and in that cJSON formation give me some error because of that my device will restart again and again
as in code if I'm input cJSON_AddNumberToObject...
Using SEGGER embedded studio for ARM (Nordic Edition) v5.60. using Project-> Configure nRF Connect SDK Project Fails in configuring MCUBoot in Zephyr.
No Documentation on...
i am working on power measurement of ble. i want to change ble connection interval in nrf blinky code say to 100ms, 200ms, 1000ms. how to achieve this and
what is the use...
I"m using SLM from NCS 1.6.1.
I'm testing HTTPCREQ with HTTPC port 443 and security tag = 1. After I reset SLM, my send is successful and passes server validation checks...
I have been using the DFU on nRF5 SDK for some years now and we use this feature to update firmware in the field.
I have sucessfully managed to get the SMP Server sample...
Hello everyone!
I'm using nrf5_SDK_for_Mesh_v5.0.0_src and I'm trying to run the Serial example. I see no Bluetooth advertising so I wanted to redirect __LOG to UART.
...
Hello Nordic team,
I am looking for an alternative method to flash the modem firmware to nrf 9160.
The issue I have with nrf connect's programmer is that it behaves unpredictably...
