here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hi
I am looking a simple way to synchronise multiple devices which might be in connected state(and streaming data) or not(storing data on flash).
I need an sync accuracy...
Hello,
I’m having trouble understanding Apple’s requirements for the advertising interval.
https://developer.apple.com/accessories/Accessory-Design-Guidelines.pdf
...
Hi
in NRF connect SDK is it possible to do the following:
recive one byte from PC via USB to a dev board. Immediately or with a delay less than 200 micro second send a...
I have a linux driver that uses nRF7002 am able to have both STA+AP. The issue I'm running into is that when I have STA up, AP MUST be the same channel, and vice versa. I...
Hello,
This is my first time taking a crack at embedded wifi, and I'm currently creating multiple wireless devices to pair with a usb dongle. The Antenna prototype is being...
Hello,
I am experiencing delays when sending data over a TCP connection on an LTE network. The issue seems to be related to the size of the data being sent – larger payloads...
Currently i am trying to implement NUS service in ble_app_hrs_rscs_relay example. what is i am trying to do: currently i am use nrf52832 custom board, nrfSDK version 17.0...
Hey there,
is there any solution to work with the BLE dongle thought testing app in Andorid ?
Need to send commands via USB to the dongle and activate test functions...
Hello!
We are working on nRF54L15, which has 50V 1.2p capacitors for the antenna matching circuit.
We also use other a few other capacitors in the antenna matching network...
Hi all,
In the PDF version of nRF54L PRELIMINARY DATASHEET v0.8, in chapter
9.1 Debug access port: in table 65: Access port overview
is listed AUX access port of AHB...
nRF5340Dk with NCS 2.6.1 and toolchain 2.6.1.
I want to measure 6 frequencies for my application, these frequencies would be attached to GPIO pins and needs to be measured...
Hi, I'm learning the nrf51-powerdown-example <system_off_wakeup_on_gpiote> from github.
My understanding of the code is:
1) When button 0 (Power down) button is pressed...
Hello, trying this and that with a qwiic relay , first a test on i2ccl then VS using a 9160DK. (i2ccl -> pip install i2cdriver ) returns a status of 0x00 that relay is not...
NCS 2.7 with sysbuild + mcuboot
NRF52840 (custom boards)
In my previous projects with NRF5 SDK I found it was very helpful to define a section in the linker so the rtt...
