Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Hi, I want write code on rust, but build system of nrf sdk for nrf5340 too hard for creating bindings, so I decide to create own HAL on rust and embed it in C with BLE stack...
Hello,
I am working on a project that I built using the nRF52DK and then created a custom PCB. The software I wrote works on the DK with a breakout board for the RTC and...
Hi,
I am using a nRF52832,and to begin with I have to erase my memory,so I connect nRF52832 and click erase all.
The result is shown below,I wonder why I can't erase my...
After trials and tribulations I have finally gotten a pulse ox device to work as I needed to. I started with the health thermometer example in the 12.3.0 SDK which is the...
Hi
I tried following the eclipse installation tutorial: devzone.nordicsemi.com/.../
And after a while I got eclipse to handle the Nordic stuff, but when I try to import...
Please find attached several fixes for bugs / incomplete protocol implementation in the MQTTSN stack that we have identified for inclusion in future versions of the SDK. ...
The Thread SDK is pretty awesome! :) However, It does has a bit of a learning curve for me because it only uses UDP instead of TCP.
While searching I found an MQTT variant...
We're developing on a custom NRF53 board. With the I2C bus disconnected from all peripherals, but with external 10k pullups connected, we get the following waveform when attempring...
Hello,
We are working on a research project in Sheridan College to create an indoor positioning system using BLE 5.1’s Angle of Arrival feature. We noticed that nRF52833...
Hi,
I am using the nrf52840dk trying to connect my bike power meter over ANT+, to then forward data to cloud (will be using the nrf9160dk and then the thingy91 once I get...
Dear Support,
I'm evaluating a tiny BLE chip that we can do:
reading multiple three SPI sensors: pressure sensor, accelerometer, and FRAM.
So with your BLE chip...
Hi,
Using 52833 it seems that sometimes the radio quits responding, ie, it is in NRF_RADIO_STATE_DISABLED state and there is
no obvious way to get it out of that state...
Hello,
I'm trying to program the ble_app_uart example program from SDK 17.0.2 in Segger Embedded Studio using softdevice 132 to a custom PCB (with the nRF52832 chip) using...
Hi,
I am using nrf9160 to handle the MQTT protocol and collect the data packets from another microcontroller using the UART interface.
Sending the data to the server using...
Hello all,
since Tuesday I'm trying to get the example project ble_app_uart_c (SDK Version 12) running. Meanwhile I can compile the project without errors, but when I flash...
