here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hi,
I'm designing a custom board and want to have debug/programming capabilities on my board. As I understand I can connect DebugOut connector of DK to DebugIn connector...
I am trying to get up and running with nRF Connect SDK for nRF52 on Linux (Ubuntu 18.04.4 LTS). I am following the guide and trying to use nRF Connect for Desktop to install...
Hi.
what i want is using 52840 dongle, test ble communication with custom board.
custom board use 52832 and it flashed BL + SD + APP.
I checked it is work using pc connect...
Hi,
we have a custom PCB board equip with nordic 52810 chip and the system ARCH is acting like Linux Host-BLE_Controller mode demonstrate below
Our manufacturer needs...
I need to send and receive data from the UART of many nodes to the UART of one specific node.
I use is the nrf52840 PDK with segger-studio. Is there a sample available to...
I'm trying to enable UART in a mesh application with SDK 15.1.0 and mesh SDK 3.3.0. This seems to be a real nightmare and I'm not sure why Nordic has so many different HAL...
Hi everyone. I'm trying to add UART Service to Mesh light switch example in Mesh SDK latest version 1.0.1. Is it possible? And When Nordic will provide integrated Mesh SDK...
Hello everyone,
I am currently working on a project, where I want to interface UART to a Bluetooth mesh network. The project is very similar to the light switch demo, because...
Hi Team,
I am working on Mesh SDK 3.10, I have requirement of mesh with Ble Uart. So I decide to take this example "ble_app_uart_coesixt". I build this example without...
Good day, support!
I have a couple of questions regarding the firmware of the nRF52840 dongle.
1) How to identify the firmware version that is nRF Connect flashing ...
After following the " Using a custom Secure Partition Manager with your application " Guide for the nRF5340-PDK, I experienced following error:
I tried to create a Non-Secure...
Hello every one.
I am new with Segger and nRF52.
I tried to create my own library for OB1203 sensor.
But i stack here when Segger view this error: Below is my screen...
As we are performing climate tests for custom PCB based on Nordic nrf52832 SOC, in low temperature i.e -20 Deg C the communication is not stable. After verifying the HFCLKSTAT...
Hi,
We thought to have a setup like this
1<-->2<-->3
1 is MESH ADV device with some mesh model
2 is MESH ADV + regular BLE stack support
3 is Gateway with...
