Hi,
I am trying to understand the pstorage to record a log for temperature. In my code, I can call pstorage_init(), and clear a block but when I try to store some data...
I would like to source a compact BLE board to act as a lock controller developed with with a matching transceiver for use in a fob and an app.
It would toggle the pio and...
Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hi,
We have a third party active power analyzer which cannot be kept in only current measuring mode. It always provide supply of 3.3 to 5V.
The DK configurations we...
Hi All,
I have up to 8 nRF52832 devices sending data back to a base unit (another nRF52832 device.) What I'm trying to do is have the remote units wakeup at a given time...
I have some questions about FSM，when I enter fsm_init() to perform fsm_any_state_find(fsm_t * p_fsm) completely in mesh_lpn_init() during debug mode by "step into"，the small...
Can you please help i use ble _ nus and after few message i need to change uart baudrate. I cloes uart then init uart with new baudrate parameter but everytime MCU goes to...
Hello Nordic team
I am working on nRF52832 dev board. SDK v-15.2.
My questions are following:
1) How much current consume if we use GPIOTE to register one pin interrupt...
Hello everyone! My team and I would like to port the SDK examples to the Arduino IDE, but we have found that the Arduino IDE does not know what board is being used. We think...
I want to use several GPIOs for different purposes.
for example, - motion detection interrupt by accelerometer - low battery alert interrupt by battery gauge.
However...
I am new to the NRF52840-DK. To burn the program into the kit, I have lots of tries to install nrfGo studio but it gives me the "no board detected readback protection" error...
Hi,
I am using my nRF52832 DK as a sniffer.
I am sniffing a BLE communication between a BLE door lock with a cellphone App.
I can see the device advertises continuously...
Hi,
I am using nRF5_SDK_15.3.0 with ble_app_uart example.When I flashed the ble_app_uart example into my nRF52840 DK it starts to advertising. If there is no connection...
Is it advisable to use coin cell battery power for nodes besides end-devices in a Thread mesh network? Where can I find technical comparison between OpenThread and BLE?
Is it allowed to use nonsymmetric capacitors to get more accurate 32k ? With 2x10pF we run some 35ppm too fast and 2x12pF the clock is 10ppm slow. We could use non standard...
Hi,
I am using SES for programming with an example of BLE Uart NUS and SAADC combined.
I can send raw data, and that all works fine, but conversion to the real ADC voltage...
Hi,
I am trying to send data from nRF52832 module to a custom application. I am receiving bluetooth characteristics but not able to get values. Value is always NULL . Can...
