Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hello,
I'm experiencing issues testing the FOTA over BLE on nrf54L15dk using the SMP server sample of the NCS v2.8.0.
To reproduce my issue, just build the sample out...
Sorry if this is documented somewhere, but there is a dot pattern that seems like a QR code on the 9160's exterior metal case. For the purposes of provisioning a product,...
I performed OTA over BLE for Matter samples available in NCS. After OTA performed successfully, it erased the Matter commissioning data and uncommissioning the device. How...
Hello!
I am working on a project based on NRF52832 MCU and NRC connect SDK in VS Code.
I have a custom PCB and I use GPIO pins to switch on the power of the OLED display...
Hello, I am studying DevAcademy Lesson 4 - Data exchange in Bluetooth LE , specifically Exercise 3 using the nRF5340DK . While attempting to build the corresponding Git code...
Hello,
We have a project which requires high accuracy for 14-bit resolution ADC output by using Nordic nrf52832, we regard that the accuracy is linked to the internal...
Hello,
I'm using nrf5340 audio application in nRF Connect SDK v2.7.0.
It has been working normally, but today when I opened folder, the sidebar disappeared, as shown in...
Hello everyone,
I guess my question is more conceptual rather than a specific issue with the code.
I am working on a device featuring an nRF5340 chip and an nRF9160 chip...
Hello, I am trying to get a custom board with an nRF5340 (on a Raytac module) up and running. I want to emulate a simple HID mouse. Therefore, I selected the code from the...
I have just started using 2.7.0 with the nrf54L15 chips and come across a few problems.
When trying to run the UART sample I found that the app overlay files, which I believe...
Other than setting the DCDC_MODE_PIN, what else does the sd_power_dcdc_mode_set() do?
I'm seeing an issue where I have a GPS peripheral on UART that is seeing about 10dB...
Hi Nordic team,
Hi Nordic Team,
We are trying to configure two SPI masters. It works when I use any single SPI (only one), but when I add the second SPI, I encounter...
Hi,
I am trying to compile an old project.
I am using SEGGER_Embedded_Studio_Nordic_v568_win_x64 with nRF5_SDK_17.0.2
I am getting an error message for the following...
Does the 7002 support 802.11 monitor mode? https://en.wikipedia.org/wiki/Monitor_mode
Some chips call it promiscuous mode even though that should be something separate ...
