Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I got the following setup: nRF52840 - GenOnOffClient (Light Switch Sample) Publish to Group 0xC001
nRF52840 - GenOnOffClient (Light Switch Sample) Publish to Group 0xC001...
Hello!
I have a complex issue that I am trying to brainstorm. The task is that I am trying to receive a file over the air and be able to serial flash my STM32U575xx.
...
I have customed my own nrf54l15 board and run peripheral_uart demo successfully. Then I tried to measure its current while running peripheral_uart demo, it was up to almost...
Hi,
I've received the nRF54L15 DevKit and tested the power consumption during sleep Testproject in GIT: https://github.com/marcel-cd/nrf54l15dk-powertest
The result was...
Hi,
I am currently migrating from NCS 2.5.0 to 2.7.0 and running into an issue where the CMakeLists of mcuboot ( https://github.com/nrfconnect/sdk-mcuboot/blob/4c7942e58c5458ce3c4e50d3169e0f865910fe87...
Hi I use nRF52832 and nRF Connect SDK v2.6.1 with visual code
I went through this exercise ( academy.nordicsemi.com/.../) and the FOTA works so far. However, in this example...
Hi nordic:
I would like to inquire about the foundry, packaging, testing, ball-mounting, and process node (e.g. 28nm, 40nm, etc.) for the 52832 chip.
（Writing an internal...
Hello,
I am using VSC on Windows with nRF Connect. Previously I have installed the NCS SDK using the "RF Connect" Toolchain manager.
I have to make changes to some...
Hello,
I'm using my nRF52840 devkit together with nRF Connect for Desktop Bluetooth Low Energy (v4.0.4) app for some testing. The app failed to recognize my devkit. It used...
Hello .
I 'm studying Zephyr .
Is it possible to run a python program in the Zephyr environment ?
I am using Nordic 's nRF5340 SoC and I need certain modules in...
Hello.
I’m new to the Nordic devices and I was tasked to develop a custom board based on the nRF9160 SiP. I took the nRF9160 DK as a reference, changing it according to...
Hi,
1. I was facing issue with my nordic device saying
[02:16:46.206,481] <err> net_pkt: Data buffer (1328) allocation failed. [02:16:46.206,481] <wrn> net_conn: pkt...
Hello. In the developed BLE software, the device uses nRF52840 and uses s140 v7.3.0.
I would like to confirm the s140 nrf52 7.3.0 release notes.
A memory access fault...
I am trying to configure interrupts for two push button (namely upbutton and dnbutton) on a custom board. In the main it is just looping and the module I have is as follows...
I am running demo nrf/samples/matter/lock.
I tried to use CHIP_NUS so I set CONFIG_CHIP_NUS =y, it worked well.
After that, I wanted to make it bondable so I set CONFIG_BT_BONDABLE...
