Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
Hi,
i am working on Pancake motor C0820B006F circuit and it is connected to P0.12 pin and ground iam usin NRF52 development board. i want to change the pan cake vibrator...
Hello
We developped a firmware on the nrf52840 dongle able to communicate with a Windows PC through the USB.
On Windows 10, we can communicate with a serial COM port....
Hi, we looking at converting our devices from a BLE communication protocol, to BLE LR with MESH networking.
Currently, we are doing the following:
Android tablet connects...
Hi,
we are ramping up production, and need to make many production jigs, and programming in parrallell since the programming of the modem takes 1 min +.
We are using an...
I am using nRF52840 Dongle as RCP with RP4 as OTBR and its working fine.
I have compiled sample/openthread/coprocessor as RCP using VS-Code. When trying the same via 52840DK...
I want to run nrfutil 91 modem-firmware-upgrade --firmware "$FIRMWARE_PATH_1" --serial-number "$SERIAL_NUMBER" on Raspberry Pi,
unfortunately. The version that can be installed...
Hi All, HW: nrf52840dk SW: ncs-v2.6.1 Issue: I'd like to be able to create a directory in my project say `/storage_part` place some files in, and during the build process...
as pic shows all parts of vscode kits are blank windows, i don't know how to fix these, any ideas? it seems the sdk and west repo already online, and in my bash i can complie...
OS: Ubuntu 20.04.6 NCS SDK: 1.6.1 Segger: 5.50c
I recently got a new laptop, which I installed using the following guide:
https://developer.nordicsemi.com/nRF_Connect_SDK...
Hello,
i'm developing a board based on nrf5340 and i want to use npm1300 as the pmic. My board is very constrained in terms of space so i'm trying to trade-off the flexibility...
Hello,
Running on the latest 2v7 release 2 light switch examples, one running the lpn overlay and the other without. Creating a scenario with lpn node and a friendship node...
Hello all,
We are currently working with the nRF5340 on a custom board and have encountered an issue with the Real-Time Counter (RTC) using the nrfx libraries. The problem...
We have an application that is looking to receive a value of 'test\0' in a custom characteristic. From the Android version of nRF Connect, I just do this with a byte array...
I have a design in VS Code that works fine on a Windows 10 computer (original development was done here). Because I spend so much time waiting for my compute to compile my...
Hello, I want to know what voltage level are the pins on DK5340 , I am using USB cable for power supply. I read that the DK is compatible with ARDUINO REV3, so does that mean...
