Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
With SDK15.3 (it appears the issue exists in 17.1 as well), we are using the flash backend. To read the logs, we are doing the equivalent of flashlog_read_cmd(). This eventually...
Hi Everyone,
I recently purchased an nRF52840 DK (PCA10056, 2.0.1, 2021.7, 68365177) from mouser. Yesterday I successfully installed the nRF Connect for Desktop v3.9 application...
Hi there,
Does Nordic provide support directly for the Taiyo Yuden EKSKDNZWB Eval Kit and the EYSKDNZWB module? The Taiyo Yuden documentation seems to suggest that's the...
Hello,
I'm trying to see serial data (polling async method) coming from a single-wire signal. I have verified via an oscilloscope that there is indeed data on that wire...
Hello,
We are using nRFSDK v15.0.0 and nRF52840 in our system. There is also an external MCU that is connected to the nRF52840 via UART. Currently we are trying to perform...
Dear Members,
I want to use SDcard with softdevice, when I run fatfs_example()
I got this :
nfo> app: Initializing disk 0 (SDC)... rror> hardfault: HARD FAULT at...
Hello,
I've been working on a simple application to scan for bluetooth packets being emitted by another system, which advertises at a consistent 10Hz. We apply a filter...
Hi,
I try to do a OTA Update with watchdog enabled . The OTA Update runs and boots image B but this is stopped after watchdog timeout (1Sek). In my code the watchdog runs...
Hello all,
I am trying to develop an application where the user will input some specific commands i.e hex value of 0x01 via a mobile application and then via bluetooth this...
Hi,
I am migrating my code from sDK15 to SDK17. In SDK15 code app_timer_start() working fine with any timer value. But in SDK 17, I am getting error code 7.
When I debug...
Hai
I'm working on nrf52832 NFC, I have a few questions.
is NFC ID in nrf52832 is unique?
can I use it for payment purposes?
if that ID is not unique, any other solution...
Hello,
I am trying to use the **persistent** flash area of my nRF52.
I created a separate zone (PERSISTENT_FLASH) in my LD script as follows:
I try the following C...
Why is the pc-ble-driver-py version 0.16.2 released to pypi , but no according tag and release set in the github repository?
Is this a stable release already? And if so...
Hi
Problem description：
Disable the softdevice before writing uicr. After uicr is written, it fails to enable the softdevice again.
Can't softdevice be enabled again...
