Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi，
sdk：ncs v1.6.1
board:9160dk_nrf9160
I use RTT to output log data, but I found that it can only output about 1k characters each time. Where can I modify it?
this...
Hi Team,
These are the SDA and SCL lines of nRF52832 connected to a sensor. the clock frequency defined in the code is 400 KHz, but its coming as 200 KHz on oscilloscope...
Hello, I have designed a custom hardware using nRF52833. I tried to program the nRF52833 using nRF52832DK, I am having following connections- nRF DK nRF custom board VTG-VDD...
Hello,
I have applied for the SUPL license and it got denied. I met the criteria which is mentioned by the Nordic.
I did log in the last 4 week and I am the member of...
Hi,
I'm trying to register the SIM card that came with the nRF9160-DK I just received and during SIM registration, it's stuck at the "still working" step indefinitely...
I have custom board with nrf52833 Soc. I was trying to implement WS2812 LED driver in zephyr which connected to ( P1.09). according to WS2812 Sample Application I copy the...
Hi all
Thanks in advance for any hints you could give on this. I would like to measure two pwm signals (frequency and duty cycle) on two input pins of the nrf52832.
board...
In the nRF5 SDK there are two uart drivers, UART and UARTE. The UARTE driver makes use of the DMA whilts the UART driver uses interupts. This is what I understood when I used...
I am considering using this part from MAXIM (MAX31343).
https://datasheets.maximintegrated.com/en/ds/MAX31343.pdf
it is an RTC plus a 5ppm oscillator output that I can...
Hi all,
Now I'm analyzing the bug that is the fault of my application's timing control.
On analyzing, I found the difference that garbage collection callback was delayed...
Hi,
I am using nRF 5340DK borad, trying to flash Direct test mode sample "nordic,nrf5340-dk-nrf5340-cpunet". My aim is the enable direct test mode on the nrF board in order...
I'm using 3 nRF52840 DK borads (provisioner,light_switch_client, DFU). I set DFU (DFU example used) as target board and connected it to PC as serial interface. I have provisioned...
Hai,
I'm facing some difficulties in programming FOTA over UART on the NRF9160 board.
Currently, by using the following command I'm trying to push the bin file via UART...
Hello Team,
I have a small issue but troubling me since a long time now. Accidently my debug terminal and project explorer came out from their original positioning. Now...
