Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Is it possible to sniff the data between two device that already connected if yes then how if no why?. What are other method for sniffing oob and passkey security based devices...
I have moved my project over to SDK 17.0. So far I have changed very little.
On compiling I straight away get a liner error: "Undefined reference to '__RAM1_segment_end__...
Hi to everyone:
As the title suggest I'm using the NRF52840 PCA10059 dongle and everything works as expected.
The issue comes that I've modified the dongle to instead...
Hello,
We have developed a new type of smartphone gamepad using the nRF52832 chip. But for some reason, it works for some games and not for others. And only partially work...
Hi,
I have problem with using nrf_serial.h, I am receiving data from Ublox GPS, baud rate = 9600, no flow control as we dont have enough IO pins.
Device is nrf52840 with...
Hello, I'm trying to integrate an SPI slave into ble_app_beacon example. Power consumption of ble_app_beacon between advertising is up to 10 uA. But if I write a byte over...
Hello
I am modifying the example of mpu6050 of sdk v14 in sdk v17.
After build, it is printed that there is no path to the file as shown in the image below.
(The...
Hello We recently went to a test facility SGS, in San Diego, with our nrf9160 device trying to get a pre-cert scanning completed to find out if there are changes needed before...
Using SDK 15.3 and S132.
I'm having similar behavior to the thread below:
https://devzone.nordicsemi.com/f/nordic-q-a/12066/gap-disconnect-stops-app-timer
After disconnecting...
hi ...
how to update the advertisement packet .. I have seen many post regarding this ,I am not getting clear , anyone can share me the piece of code which will help me
I am trying to repeat the example in the tutorial: using board: nrf9160dk_nrf9160.
nRF Connect SDK Tutorial - Part 3 | NCS v1.3.0 --> 1.2 Walkthrough for BME280 - but gives...
Hello,
Our setup:
-nRF9160
- Zephyr OS
- Segger Embedded Studio for Arm (Nordic Edition)
- SDK v1.3
Questions
1) which are the differences between Zephyr functions...
I'm designing a product around the nRF52840 (PAN1780 module), and using the PWM to drive a piezo sounder (using 2 pins as Hbridge). When I start using BLE functions, I get...
Hey, Yesterday we decided to update SDK to 17.0.2. After this change our FreeRTOS stopped working. We started investigating where is the problem and we found that when vPortSetupTimerInterrupt...
Dear all,
I'm currently using nrf52840DK with SDK 17.00 and s140 softdevice. I'm trying to syncronize the dispatch of my data with connection interval (set to 7.5 ms). I...
