Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
We need to install nRF Connect SDK v1.2.0 on a new machine. I followed the provided steps, using the Toolchain Manager (previous "Getting Started" method is deprecated, apparently...
Hi everyone,
I was looking at the SAADC example and I need to modify it in order to fit my design. I want to perform analog readings from eight sensors using an eight-channel...
Hi,
I'm developing a BLE application that is also using FreeRTOS.
I also need to use PWM to control an LED (mainly because the requirements define LED patterns, which...
Base BLE structure ble_advertising_t contains a member structure ble_adv_mode_config_t. This structure contains two parameters that are meant to limit number of advertisements...
Hi Team,
I want to create on flash section to store the specific data like Crypto Keys and Serial numbers. How to create one page/section in existing Flash memory without...
I am trying to test a BME280 sensor on the nRF9160. I followed the steps where I created a folder (board) and added the nrf9160_pca10090.overlay and add couple of line in...
Hi, I would like to implement free rtos on nrf 51 using IDE Segger Embedded Studios. Could some one please direct me to the necessary links/ information.
I have researched...
Hi ,
I am working on project which is based on nrf9160 Development board.
could you please verify these points-
1. I am sharing the snapshot of the registers...
I have downloaded the Keil compiler and the Nordic key for same.
When running Keil_v5/UV4/PackInstaller.exe I can not get the update:
Cannot download file developer.nordicsemi...
Good Day,
i´m want to use saadc with 7 channels. I´m using the ADC Driver with an interupt handler. All 10ms the sampling starts per cpu. I use the configuration followed...
Hello,
I am running on a NRF52840 DK a Zigbee program configured as a router. For the coordinator i am using the cli example from the SDK.
On the router, I have developed...
Dear Nordic Semi, ladies and gentlemen!
I'm working on a prototype device with USB host functionality. I am using Arduino USB Host Shield connected to nRF52840 DK . DK is...
Hi，
We want to confirm the effect of GPS fix_interval and fix_retry, so we start GPS with parameter fix_interval=10s, and fix_retry=30s, then get the result as the following...
I try to bonding.
Using SDK 15.3. 0 and S332 Softdevice.
I successed bonding procedure used Peer manager.
after bonding, If I try to connect one more, nRF Connect app...
