Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
I am using peripheral_uart as my base project. Right now MTU value is 23 I believe as I can receive only 20 bytes of data at a time. How I can increase the MTU size with configurations...
Hello,
in use is the nrf connect sdk v2.6.2 toolchain v2.6.2 on my nrf5340DK
I struggle transmitting ADC data from my nrf5340DK via USB to my windows PC. On my PC there...
I've added some debug information to the build of my application. The added stack usage has caused some threads (USB, BLE) to overflow the stack and cause random crashes....
Hi,
Is there any better block diagram of how power is managed and routed within the nRF7001/ nRF7002 device ?
I see it has a buck from BUCKVBAT fed back to several other...
When trying to open certain c or h files in my project, Segger Embedded Studio (latest version) gives a very longwinded uncopyable dialog message that there was an error decoding...
Reopening this issue from three years ago
as the original question was not answered.
So I had this line of code after sd_softdevice_is_enabled 'returns' false
but...
I am trying to communicate with multiple devices using ESB. The host device must queue data in the TX FIFO as ACK data before receiving the data. I want to keep data queued...
Hello! I am developing an application under the SDK V2.9.0. Now I am trying to set up a simple project with a sysbuild, Mcuboot and a partition manager. Here is the file tree...
Hi,
I’m currently using nrfx libraries when there are no equivalent options in Zephyr drivers, and I found similar drivers with the nrfy prefix. What are the differences...
Hi
I would like to use DeviceTree in VS code. The VS code had installed "nRF Connect for VS Code Extension Pack" and tools chain.
But I can't see any file in "DEVICETREE...
Hi Nordic DevZone Support,
I am facing an issue with my custom PCB using the nRF52840 microcontroller and Zephyr NCS v2.6.1 . The same firmware works on other PCBs , but...
Hello, I am working on nRF52840 and using nRF Connect SDK v2.9.0.
I want to know how I can configure the UART to be half-duplex tx or half-duplex rx.
I checked the APIs...
Hello Nordic supporters!
We are developing a system using BT Mesh alongside a software DALI protocol driver with certain timing requirements.
Right now we're trying...
Hello,
I am trying to build the Wi-Fi Bluetooth LE coexistence example using the nRF54L15 DK and nRF7002 EB, but I encounter the following error: zephyr_pre0.elf section...
This is not a support request.
I just want to share some code that others might find useful. If I post it here then they might find it.
The current RADIO_TEST example...
