I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
Hi, I have a question about nRF Connect Programmer tool.
[Description]
The device memory layout shows the address range as "0x00000000 - 0x00100000 (size 1048576 bytes...
Hi,
In our application, we are using HID to control mobile phone or PC.When users connected our product, it will automatically connect next time.
But our product is battery...
Hi
I am using Zephyr samples (common with the samples found in NCS) to evaluate the advertisement function of nRF52833DK.
I have run these examples:
Bluetooth: Periodic...
Hi,
After updating the FW as shown on the video, LED3 is NOT blinking, trying to connect (LTE).
If I open the terminal window, select the board, and pressing the Reset...
Hi,
We are using the GPS xample for the nRF9160. and are struggling a little with getting the GPS fix.
$GPGGA,001932.00,,,,,0,,99.99,,M,,M,,*6F $GPGLL,,,,,001932.00...
Hello to all the Nordic Jedi knights!
I have a question regarding the PPK2: Is there a way to disable auto-ranging and manually select the measurement range?
I know that...
Hey,
I have a custom board with nRF52833. Sensor is connected to: P0.11 (pin 19) - SCL P1.08 (pin 17) - SDA
with code below I don't get any `NRF_SUCCESS` back.
I saw...
I'm trying to build a new device that I bit, bang the I/O Also others to just have simple signal controls.
Below is the portion of my dts file. The example here is the onewire...
Hi,
I am using nRF52810 (s112 softdevice) with SDk version "17.0.2".
How do I set BLE advertise in continuous mode(if not connected then advertise continuously until it...
Hi
I am trying to declare a custom cluster in zigbee and enable the reporting for some attributes of the cluster, i followed this post to create the custom cluster devzone...
Hi guys,
I'm researching the maximum direct connection distance between two Android phones for transfering small amount of data - which lead me to BLE Coded PHY S8 as a...
Hi,
I m using nRF52840 dongle to setup the nRF5_SDK_17.0.2 .
Besides, the related software and the Segger Embedded Studio are installed.
Occurred Problems :
When...
Dear members,
How can I wake up the system after idle ?
It goes to main loop, but never wakes up if there's a signal from HRM,BSC or B.Power after search time out and...
