I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I'm trying to make a BLE device that actually pairs securely. I posted this question on StackOverflow but didn't get any answers - maybe someone here knows more. As far as...
I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I've developed a custom service and DFU using secure bootloader. I've started developing it for nRF52832 and all was working. I was able to generate .zip file and update the...
Hi,
Kit : nrf5340
SDK: nrf connect SDK
I While testing the timeslot example in nrf samples part, I am getting the below error. Kindly tell me the procedure...
Hi!
I'm close to finishing a project where every type of messaging is done using simple BLE broadcasts (using my own frequency hopping and other features.)
However I...
Loss of comms between nRF24L01+ transmitter and receiver after successful data transfer.
One rf24 is configured as a PTX (sensor device) communicating in a simple point...
Hello,
I need to implement, say, 100 LPN + proxy and 1 friend + proxy, LPN are metering devices.
How can I send a value from a sensor to my phone without sending a request...
My project starts to grow and I would like to separate different parts of code into modules. Each module will present one .c file together with its .h file. In some .c files...
Would you be able to clarify why the Azure IoT hub is marked as experimental in NCS v1.5.0 on the menuconfig?
And is there any features missing or not verified etc?
And...
I am using S132 v7.0.1 on an NRF52832 to do a basic scan for BLE advertisements for 30 seconds (10 seconds on each primary advertising channel):
This works fine and as...
I am developing a custom board with NRF52832 and an audio DAC which outputs to a headphone jack. When the headphones are plugged in I can't program the board with my Segger...
Hi,
I have updated our SDK version from 15.0.0 to 15.3.0 for our custom board based on nrf52832
I wanted to rebuild the bootloader just in case it was needed. So i have...
Hi,
I referred and tested the File system Shell example on nRF52833-DK. In its source code, in file 'main.c', the function main() is empty/stubbed. Is there any way to customize...
Hello ALL,
I am trying to use MCU boot with my application. I am using NRF916DK and it has external Flash similar to NR52840DK board. Now when I am creating a partition...
Hi, I'm using BC805M module (nRF52805 SoC). I understand that the nRF52805 doesn't support BLE mesh. I would like to ask about the availability of using BLE (S112/S113) for...
Hi, I am in the process of evaluating nRF5340 to switch from STM32 device to nRF device as per my ex-colleague recommendation. I started looking at simple blinky example for...
I am using nRF connect v3.6.1 but the following error occur when i open the device in nrfconnect as follows:
Error :Unsupported device. The detected device could not be...
