Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
Hi engineers,
I want to use the pin P1.09(NRF_GPIO_PIN_MAP(1, 9)) as GPIO, but when I initiate it, it seems fail.
I've looked through the relevant issues here, but got...
Hi,
I am currently trying to build a project using a nRD9160 with legacy code and am receiving this error when trying to load an existing project:
I understand...
I am not able to successfully use your nRF UART app to communicate with your nRF52840 DK. I get a warning when installing the app that it may be too old for my version of...
I'm still learning BLE development so I apologize if this is a basic question.
Here is a screenshot of a recent capture I did with the nRF52-DK. The bluetooth sniffer is...
Pardon my ignorance of the nuances of Security and Encryption but what I am observing is a bit perplexing.
Every time I run the nrfutil command to generate the bootloader...
Hello, I use sleep_mode_enter() to put the device into sleep mode, however, the RTT print a fatal error after sd_power_system_off(), I don't know whether the device is in...
I'm trying to open a nRF Connect SDK project in Segger Embedded Studio for ARM (Nordic Edition) V5.30a
When I try opening the project I get an error box with the following...
I want to add an OUT endpoint to the USBD example, but it is not successful. I cannot find the relevant tutorial. Below is my main.c, asking for help, thank you very much...
hi nordic team,
im update the app by usb dfu,my sd version is s140_nrf52_7.0.1_softdevice,and shell like this:
program.bat
dfu.bat
the device cant update and...
Hi,
Working on RSA encryption, I'm trying to build an RSA context from just the P, Q and E part of the key (as per https://tls.mbed.org/kb/development/how-to-fill-rsa-context...
Hi Nordic Team,
I've modified the DTM app to use USB CDC, I used a serial terminal to manually send commands, e.g. set tx power command, it worked fine. But it didn't work...
I'm a newbie to nRF stuff so please forgive me if I have missed the obvious...
nRF52840, SDK 17.0.2
The Nordic infocentre lists 4 options - SAADC driver - legacy layer...
Hello,
I am trying to observe communication between the nRF9160 and nRF52840 on v0.8.2 of the nRF9160-DK board. According to the schematic and documents, P0.23 should be...
I am putting data in a queue whenever I get indication, something like this:
on_indication(..,.., received_data)
self . qure_received . put (received_data )
Is there...
Hello
I'm trying to send a dataset from the nRF51-DK over BLE to an iOS device. The total data to be sent is around 500 kB. What is the best method for transmitting this...
