Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hello,
I have following problem.
I use the nRF52840 DK and want to run it in nRF only mode, so I have the minimum power consumption. If I set the DK to low power mode...
Hi,
I encountered fota_evt_handler in azure_iot_hub.c is missing the call to azure_iot_hub_notify_event for the AZURE_FOTA_EVT_ERROR case, resulting in the application not...
I'm currently working with the MX25R6435F flash chip on board the nRF52840 DK and I'm running into issues with it. I don't know whether it's down to my lack of understanding...
Hello,
I am using nRF52832 integration. While drawing the PCB, I could not find the pin definitions in detail in the datasheet. Which pins correspond to SPI, I2C, and UART...
What is the main clock frequency when application is running in thingy52? Is there a way to measure it from GPIO?
BTW, want to know what is the clock source and setting...
Hello,
I'm using SDK for Thread v4.1. I built my project on top of multiprotocol example "ble_thread_dyn_template". I want to increase the radio output power of the device...
Hi,
I have a custom board with nRF52840 and I'm using nordic SDK. My image size is increasing because I have lots of peripheral connected in my board. I would like to use...
Hi, I'm about to perform an RF-PHY test on a module using nRF8001 to get a QDID. In that connection, I would like to know the specifications of the nRF8001.Can you tell me...
Hii ,
Iam using nordic nrf52832 board In the example of ble_att_mtu_throughput example . I have tried a lot to achieve the 803 kbps, but the output was 204 kbps only....
I want to implement integration tests of the ZigBee subsystem on nrf52 and looking for a way to launch them by CI script. We need such a feature for automatic testing after...
If we were to run a 52832 as a BLE advert receiver - listening permanently for BLE adverts - do you have any information of the expected current consumption in this kind of...
Hi!
I want to program boards in production by using the SWD interface from a nRF52840. The image will be sent from a PC to the nRF through the USB-virtual serial port. ...
Download nrf52832 through JLINK tool, and then through jflash read back, it is found that the bin file is different from the download in bin file. What is the composition...
Hello, i work with nrf52840. I know that it is possible to run two stacks Thread and BLE on one Chip (nRF52840) on dynamic way. But i want to run Thread as NCP-Radio and BLE...
Is there a graph available for the internal power regulators efficiency / current consumption at different supply voltages and temperatures for the nRF9160(-SICA)? We're currently...
