I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Hi,
I'm preparing to run some openthread code on an nRF5340DK using the latest SDK and toolchain v3.1.1. A simple program works fine until I set the CONFIG_OPENTHREAD...
Dear Sir,
I have purchased nRF5340 DK (Will call it device hereafter) and am trying to bring it up.
I have connected the device to Linux but the device was not detectable...
I’m testing the nRF9151 DK in India and trying to use the nRF Connect app (Quick Start guide) to connect the device to the network.
Board: nRF9151 DK
SIM: Onomondo...
I have a nRF52DK board that I loaded the peripheral_uart program in a while ago. I tried to get the board running again but when it calls err = settings_load() it just keeps...
I'm currently trying to integrate Memfault to my project that is using nRF9151 DK. Memfault was working fine until I turned on these configs:
# Collect LTE Metrics CONFIG_MEMFAULT_NCS_LTE_METRICS...
The application here is reading a Manchester stream on a GPIO. which comes from a MAX41473 radio IC.
Decoding is working fine using GPIOTE, timers & PPI to time & decode...
Hi,
I have two nrf9161 dev kits. I have flashed the firmware 2.0.1. Then I flashed the hello_dect example.
Now I always get an error and the program does not start. *...
Hi,
I am able to do some stuff partially using the command
$ west build -b nrf52840dongle_nrf52840 -- -DDTC_OVERLAY_FILE=usb.overlay -DOVERLAY_CONFIG=prj_cdc.conf
With...
Hi guys, I am using the SDK v2.9.0 and the toolchains b620d30767. To add the build configuration for the sample peripheral_uart, the console print some error log.The log as...
Hi all,
Im' tryint to acheive a aws fota firmware update on my custom nRF9151 board but I'm stuck. Here is my setup and what working
- Custom board build with a nRF9151...
Hi,
I would like to perform channel sounding on nRF54L15 DK,
I tried to compile sample "channel_sounding_ras_initiator" in nRF Connect SDK v2.9.2, but error message says...
I'm getting an error when I try to push my branch.
remote: Permission to NordicDeveloperAcademy/bt-fund.git denied to batir.
fatal: unable to access ' github.com/.../...
Hi, I am looking to setup my nvim installation with a debug config to match ozone, but need some help getting started. When I debug using VSCODE I seem to miss crash, reboot...
For an application developed using the latest nRF Connect SDK v3.1.0, how would you recommend configuring Bluetooth performance to maximize connection range for nRF52840DK...
Hi,
I'm trying to pass to v3.0.0 from 2.6.0. I've install the new toolchain from nrf connect desktop app, everything works. I go to vscode add new build configuration, selected...
