Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello All,
Thank you in advance for your time and interest in this issue and willingness to provide suggestions.
We have a product that uses the nRF52832 processor in...
Hello,
I'm trying to connect a sensor to the nRF9160 board using the example Asset Tracker v2.
My sensor (SHT30) is connect in I2C to the pins 31 (SCL) and 30 (SDA). In...
Hello,
Does nrf9160 support C++? If it does, which version? I saw a similar question over 2 years ago in which C++ was not recommended ( https://devzone.nordicsemi.com/f...
SDK: v17
Softdevice: S112
I am currently checking the throughput using nrf52810 or nrf52805.
In device A, data is input as Uart and checked as device B input data...
Hello everyone! I want to evaluate the exact power consumption from the camera (Arducam Mini 2MP OV2640) using the nRF52840-DK as well as its SDK with the nrf52-ble-image...
Hi,
I am trying to implement USB DFU on a NRF52833 with nRF5 SDK for Thread and Zigbee v4.1.0 and nRF5 SDK v16.0.0.
In a first step I want to perform this on the devkit...
Hello,
I have several issues with the new nRF Connect for VS Code SDK, I put them into one ticket, although, some of the issues could be related directly to nRF Connect...
Hi
1: According to this ticket: https://devzone.nordicsemi.com/f/nordic-q-a/28335/nrf52840-usb-pins-impedance you recommend to not
have any serial resistors on the D...
Hello!
I have installed Android nRF Mesh application version 3.0.3.
Also I bought Yeelight YLDP10YL lamp which is qualified mesh product ( https://www.bluetooth.com/learn...
Hello,
I am getting a bit lost in the pool of different versions and libraries. For simplicity, I just want to achieve a single goal to start which is send a bluetooth packet...
Hi
1、 I want to know the connection mechanism of one Central connects multi Peripheral.
2、What is the time interval between one connection switching to another? Is there...
Hi Guys,
i am using nordic nrf52840 controller. and i have my own bootloader application code.
and once the controller boot up then it start mbr code from 0x00000000...
Dear Nordic Team,
Is it possible to have dual role (one at a time) on nrf52805? Is any such stack available?
I am very new to BLE and i am facing a problem in BLE Uart...
