I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
Hello Nordic!
I have been developing a Zigbee application and now, I need to connect via Serial communication with another device. I just need to listen to the port, not...
I am using flash_fstorage_s140_pca10056 example from SDK v17.0.2 , I see that the start address is 0x0003 E000 and the end address is 0x0003 EFFF respectively.
I want to...
Hi,
I am trying to check how DFU works but I have problems setting it up. I will describe all the steps that I have been doing here, so that it will be easier to try to...
Hi, I am designing a custom board usign the NRF52832. Im using this externar crystal https://es.rs-online.com/web/p/unidades-de-cristal/1753468/ . but I have seen that many...
Hello Nordic Support Team
I need desperate help to get my proof of concept working. I have been able to prove that the applicational concepts work on the nRF52840 and now...
I'm trying to create an application on the nRF52840 that can read serial input from an external GPS chip and also provide log output via USB. As I understand it, the UART...
I want to read access address of a connection between master and slave in master.
I need access address and not the MAC address after connection establishment.
Is there...
Hello, when developing our application, we run into a problem. We are running Zephyr 2.4.0 on nRF52840 MCU. We use LSM303AGR sensor, which is supported by zephyr LIS2DH driver...
Hi,All:
1. As the topic, now i just make bootloader,How do i perform a app entrance? and how to staging, combing.........in the picture as below. Or,on the other hand,how...
Dear,
I am trying to manually toggle GPIO0_2 by writing into the GPIO register, 0x50842504[bit 2]. The output of GPIO0_2 was always static in either high or low.
If...
We use the Nordic library for mesh with Gatt proxy service to our mobile device. We've noticed that unsegmented messages are only serviced and sent every 250ms through the...
Hi, I have made a super hex file and getting the following issue. I have already made a super hex file successfully already but this time getting this error. Does any solution...
Dear friends,
I want to store the sequence nunber in flash, from the case we can know the mechanism.
I found a strange phenomenon that I flashed a serial example( nrf5_SDK_for_Mesh_v5...
Dear friends,
I used my nRF Mesh app provsioning a new device, now, I can export the Json format configuration data of the Mesh network from nRF Mesh app, I want to use...
Hi,
On button press, the button handler event calls the "ble_lbs_on_button_change" function which sends notification to the BLE client.
The value of the button state...
