Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
I have a bit of an odd one, and would appreciate any input. We have a fairly complex project, which does various things, but some of the time, I get a hardfault. The issue...
I am getting linker errors such as the following:
Output/Release/Obj/saadc_pca10056/nrf_sdh.o:SDK\components\softdevice\common/nrf_sdh.c:83: undefined reference to `start_sdh_req_observers...
Hello i have a keyboard with nrf52840 with ZMK firmware, BLE, adc, gpios, i2c0, usbd, DCDC and CONFIG_CLOCK_CONTROL_NRF_K32SRC_RC
When it is connected with the computer...
I would like to know the natural interrupt priority among different peripherals of nrf52840.
Specifically I am looking for default interrupt priority between RTC1 and TIMER1...
Hello, guys. I'm using the PCA10040 and the SDK 16.0's BLE UART peripheral example. I am trying to make PWM signal below.
When PWM0 stops, PWM2 works, and when PWM2 stops...
Hello everyone,
I am working on an nRF52-DK and getting familiar with Zephyr. In this process I am currently trying to extend the BLE MTU size beyond the default 23 bytes...
Hello,
My device is a USB HID peripheral connected to a PC. There is a case when the PC is turned off, but USB power is present. I want to detect this situation.
At the...
Is it possible to detect the presence of a Low Frequency Crystal and configure softdevice to use if present, otherwise use the internal RC oscillator?
A proposal would be...
Hi,
we have troubles to use 4wire NRF LPUART between nRF52840 (client) and nRF9160 Serial LTE Modem app (server).
We use v1.5.1 of nRF Connect SDK.
For nRF9160 we added...
Hello Team,
I want to know while Ble device is connected to the android device and within 5mins if device not get any data from android device then,
- Can device enter...
I am using sdk for mesh v.5 (s140.7.2.0) and nrf52840 DK and want to add uart peripheral into the client in the light switch mesh example and then trigger button 1 once a...
Hi,
I have written Hitachi AC IR transmitter using Smart remote 3 library.
Smart remote 3 library support 2 AC protocols, i.e., SIRC and NEC.
Kindly guide me how...
Hello, I essentially want to figure out a way to use the NFC buffer received by code like the writable_ndef_message example and have that same buffer, in the same code, advertise...
