Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hello,
I'm trying to measure execution time of a piece of code in nRF52832. I was searching and found that I need to get the start time and finish time by using
beginval...
Hi,
I am using nrf52840 Preview - DK, with SDK v15.3.0 and Softdevice API 6.1.1
As we need to set NRF_LOG by setting the NRF_LOG_ENABLE and NRF_LOG_BACKEND_URAT_ENABLE...
Hi,
currently, i'm developing nRF52832 chip and I trying to use two GATT services.
I want to know about that "Can I use my custom services with Nordic Uart Service"...
I am basically wondering what the difference between these two examples in the SDK are?
Also, I see in both cases after the spi_transfer is called there is the following...
Hi Support team,
When I installed the nrf Connect SDK v1.2.0 with the Toolchain manager, I found that the files in the directory indicated were incomplete.
As shown in...
Hi. I am working on adding DFU to our application. I want to use buttonless dfu service for entering bootloader. I think the only thing one need to do is write a correct widely...
Hi,
I have a setup where one nRF52 based device is a master and generating a time pulse with a counter. On another side, I am having Android device with QCA6174A module...
hello team,
I'm using nRF CONNECT 3.3.0, SEGGER Embedded studio IDE with Cmake version 3.16.5 and SDK
my device (nRF9160DK) is connected with system but SEGGER Embedded...
Hi, I've successfully passed nRF Connect SDK installation by using GSA application (macOS 10.15.3, python 3.7.7, west 0.6.3). Now I'm in the SES 4.52c and have a problem in...
It looks to me that in NCS/Zephyr it is only possible to configure the system clock to operate off of the LFCLK. I haven't been able to find any Kconfig options that would...
We have 2 identical development boards and have been using only one until now. I was able to download code into the 2nd board successfully but it will not run. It does not...
Hi,
what is the valid range of interval for NRF_SO_GNSS_FIX_INTERVAL? when we set it to 5 it will failed, but 1 and 10 can be successful.
here is the code and error log...
I have a nrf24 transmitter and receiver that I want to set up for max speed. I have my SPI's both at max and I set the crf24 register to reflect 18db (was not sure how this...
Hi,
I am setting up nRF connect SDK into Mac, however I received an error below when setting up a project in SEGGER:
Could you please help me to remove this error...
