Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello , I want use nrf24lu as "Hos" and nrf51822 as 'Device'.
I need some info about nrf24xx whith gazell .but I can't find info bout those param like:
typedef enum...
When you download win driver (from www.nordicsemi.com/.../72324929 for instance). There's only a win32 dll/lib provided.
However, modern development are often made on 64bits...
hello, Nrf24LU (Rx) , nRF51822(Tx).
The Nrf24LU Can only receive one packet。
if I use this function twice ， like this：
The Nrf24LU can receive Continuous.
I guess The...
Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
Hi,
We are developing a mesh network. Our requirement is the one device can connect to three other devices. Using one connection as a peripheral and up to two connections...
I am working on iOS pairing and bonding and connection and disconnection through UART.I am facing issue where pairing is initiated after that the device is getting automatically...
Hi,
We are experimenting with Distance Measurement feature a we observed 2 issues.
HW: Custom HW with: CR2032 coin cell -> joulescope -> 40 uF capacity in ceramic caps...
Hi all ,
I 'm experiencing issues with MQTT client connection on an nRF9160 board via LTE -M .
Some context : I 'm trying to connect to a MQTT broker via LTE -M (actually...
Hi , I am wondering if anyone with SPI expertise can answer this Q , I 'm using an nRF52840 with spi_transceive_dt()
In my devicetree I've configured SPIM on SPI3 to talk...
Hello,
I used the default sample from the nRF SDK with the same prj.conf file. I can flash it to the board successfully, but I'm seeing an error in the terminal. My toolchain...
nRF5_SDK_17.1.0\nRF5_SDK_17.1.0_ddde560\examples\peripheral\blinky_freertos
nRF5_SDK_17.1.0\nRF5_SDK_17.1.0_ddde560\examples\peripheral\blinky_rtc_freertos
I burned these...
I am using nRF52840 to interface my MPU6050 sensor via I2C , I build and flashed the program and there were no problem. But I can't see any clock signal on the default I2C...
I'm trying to build the zephyr/samples/net/sockets/http_client. I selected thingy91_nrf9160_ns for the board config and it builds and works fine. However when I enable
...
In my project, need an external sram with SPI interface to increase the sram volume.
I'm not sure if I can do it，please give an exsample in C language and some tips.
An...
Some of the products we produce do not work after about 10 days. Our firmware starts the watchdog module as soon as it starts, and sets the timeout period to 30s. And read...
I would like to implement ANALOG Modulation schemas on nrf52 serias family (e.g. AM, FM, SSB)
Do I have a direct access to IQ samples OR basic properties of the radio carrier...
I am using is25lp03d flash with "nordic,qspi-nor" driver.
The issue is that nrf_qspi_nor.c driver uses `nrfx_qspi_mem_busy_check()` before entering suspend mode. This function...
The %XCONNSTAT read command returns the total amount of data received/transmitted "in kilobytes". By kilobytes, does the documentation mean 1000 bytes or 1024 bytes?
