Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi,
I am working on NRF52832 board in segger embedded studio. I am using nrf SDK 15.0.0.
I have created BLE custom characteristics and using nrfConnect mobile app to communicate...
Hi,
I am using nrf52840 Preview - DK, with SDK v15.3.0 and Softdevice API 6.1.1
I have modified the 'ble_app_blinky' example to have an advertising interval of 500ms...
Hello I am currently trying to combine BLE, SPI and TWI programs into one. I used SDK 15.0.0 and confirmed that each program works properly with keil. However, since keil...
Hi,
I meet a problem:
nrf52DK runs a rtos similar with nuttx. The debug environment is ubuntu 16.04; the debug log is printed via minicom.
When the JLinkExe is not opened...
Hi,
SDK 0.4.0 simple_mqtt project
Modem mfwnrf916007029alpha
I want to write an unique 4 bytes ID into each nRF9160 via nrfjprog.
So that, I can set subscription...
If the peripheral makes a connection with the central (the peripheral sends a packet, the central responds, and the peripheral sends a second packet) What is the calculation...
Hi and happy new year everyone,
I am a developer for Raytheon Anschütz GmbH in Kiel Germany and working on a Zigbee mesh sensor network. Unfortunately I am an absolute beginner...
Hi, radio experts here. Due to some limited conditions I have to implement one custom radio communication pattern in MCUBoot, not the BLE stack which is a bit too heavy for...
Hi.
I have some question.
I use Thingy52 module.
I want to use(merge) all service in Thingy:52 SDK v2.1.0 into Nordic-Thingy52-mesh-demo in Thing_bridge.
I'm trying...
Hi,
I have tested the following solution and it doesn't work if I try to load more bytes.
case BLE_EVENT_DATA_COUNT_HANDLES:
printf("BLE_EVENT_DATA_COUNT_HANDLES\n...
hi
I want to know where the gazell control the GPIO06, i connect a LED with this pin ,and its blinky when send data failed .
I used to see it controlled in somewhere but...
Hello,
in my design I used the antenna swra117d from Texas.
I am able to connect to my custom board with the nrf52 dongle and the nrf52 DK.
Unfortunately I can not connect...
I followed the recommended steps and got the at_client solution to build and flash in Segger Embedded Studio with tag "v0.4.0".
I installed it onto my board, and but didn...
Hi,
I'm currently programming a custom board using a nRF52832 ( using this wiring ). Everything was working great but I tried to play with SAADC and maybe did a wrong...
I am using the link below
https://infocenter.nordicsemi.com/topic/com.nordic.infocenter.sdk5.v15.3.0/getting_started_softdevice.html#getting_started_sd
with 3 options...
