Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
nRF52 DK, PCA10040 v1.2.1
PPK PCA63511 rev 1.1.0 2018
I am connecting the PPK to the NRF52 DK in the simple case where I want to measure power consumption of the 52832...
I'm trying to get nRF sniffer to work in wireshark. I followed all the steps from the nRF sniffer user guide, but I can't get it to work.
The issue: - when I have the PCA10040...
Hi,
I tried to build your own example about "fatfs" on my board "nrf52840pdk" ( with MyNewt as OS ) but it seems that "ff.h" can't be found. Has it got any dependencies...
An nRF5 SDK for Mesh v2.2.0 dimming example client running on a nRF52840 Preview DK is not detected for provisioning by a nRF Mesh smartphone provisioner.
Running the example...
I am in process of doing my eng. thesis and apart from setting up Thread network part of my work is to measure delivery time of messages.
For now I have an application based...
Hello!
I am using NRF51822 in receiver mode with enabled interrupt on ADDRESS event, and even if transmitter is switched off I still get a few messages every second. It...
hi........
i have customized one program ....using segger 15.2 ...nrf52832
when degug it,the code from button and leds stops at nrf_breakpoint_cond ... even it doesn't...
When performing pre-qualifying Bluetooth radiotest of our hardware (utilizing the nRF52840-chip) at NEMCO, we experienced very strange behavior. The frequencies detected in...
My setup of the buttonless BLE DFU secure bootloader using SDK15.2 isn't launching the application after a successful OTA package transfer. Using RTT and breakpoints, I narrowed...
Hi ..
I am using nrf52832 and peripheral device sensor ..segger 15.0
Is it possible to wake up from sleep by interrupting the sensor .. possibility is there ??
Hi,
I am shifting my program from version 11 to 15.2. While including SPI files to the ble_app_uart code, I met with this issue. I have enabled all defines for SPI interfacing...
I'm trying to get the ble_app_uart example working on a nRF52810. I'm using SDK 15.2.0 together with Softdevice S112.
The infocenter says the Example needs Softdevice S132...
I'm facing the issue, that the app_ble_uart example just works if I hook up TX/RX of my USB - UART converter. Is this a desired behaviour? It doesn't seem to start and advertise...
