Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hi,
I am new to the nrf52 platform.
I am working on adding just works pairing and bonding to my BLE peripheral code. I tried to take reference from ble_app_bms example...
I have developed a data logger using nrf52832 s112 sdk 17.0.2 (nus service).It logs data upto 1mega Bytes,we have a custom buit android app with which we download the data...
Hello,
I am working on nRF52840 custom board, in that, I was facing issues with sd_softdevice_enable().
When I call the sd_softdevice_enable() it's stuck. Not return from...
Im using SPI interface to read data from https://docs.rs-online.com/7d34/0900766b81327f26.pdf using the D2 opcode.
The opcode starts reading the page from the flash (528...
Hi,
we are not able to see any output in NRF connect APP in FFBM mode with DTM Firmware,
However , on flashing complete firmware, we are able to turn on Beeper in FFBM...
Hello Nordic support,
I have a Zigbee coordinator application which has declared the time cluster as a server. I have a zigbee end device which has a time cluster as a client...
Hello I'm using nRF53 DK on zephyr v1.6.1. I'm now testing the power-saving mode. I tested the system-off example "v1.6.1/zephyr/samples/boards/nrf/system_off" and it works...
Hi,
I am using nrf52810 chip. we are trying multilink with central(1 central and two peripherals connected at a time),one central and one peripheral is fine, but we are...
Works on Huawei P20 Lite (Android v9), Samsung J3 (Android v7.1.1), all IOS phones. Doesn't work on Samsung A50.
Samsung A50 does see the devkit when using the same firmware...
OK, full disclosure - I'm pretty new to the whole nRF Connect/Nordic Semi environment, having had to jump across here after all the issues with silicon availability meant...
I would like to configure GPIOs as compatible = "nordic,nrf-gpio"; in devicetree file.
I did check this topic, but I think that this kind of configuration defeats the whole...
Hi, I'm working on a FreeRTOS (I just start to use it, so I'm a beginner) project in wish we want to use an external 32 MHz crystal. The program has a task that should be...
I want to implement CENTRAL using nRF52810. To implement the central, the softdevice must be s132 but I am not familiar with the softdevice concept. Until now, the softdevice...
Hello,
I closed below case by mistake.
nRF9160 receives garbage data on UART sometimes - Nordic Q&A - Nordic DevZone - Nordic DevZone (nordicsemi.com)
As per your...
