I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hi,
I need to connect nrf52833 (BM833 module) with host controller. what are all the interfaces needed to communicate with host controller? help me out in this.
Kindly...
I used 2 channel saadc, channel 1 and channel 3.
Maybe in the first few minutes, it's done ok,
p_event->data.done.p_buffer[0] is belong channel1 adc value
p_event->data...
Hello,
We have integrated the FATFS example as shown in the usbd_msc example project into our own firmware application. It works perfectly on the nRF52840dk and when we...
Hi,
I want to check time line of my project using segger SystemView.
- SDK 16.0.0v
- ESB example
- nRF52832
When Start recording, "Could not find RTT Control Block...
Hello Team,
I want know how to use RESET pin [pin. no. 21] as a GPIO.
I followed below thread but it not work for me!
devzone.nordicsemi.com/.../disabling-pin-21-of...
Hi:
What's the marking on the nRF24-LU1+?
Marking exactly "nRF24-LU1+" or any chance marked as "nRF24-LU1" instead? Your big assistance & prompt feedback is much appreciated...
I am using NRF52810 in : In advertising mode not able to erase or write to flash sd_flash_page_erase. hungs up via processing commands from nrfx_twis_state_machine
Hi,
I'm developing a custom application starting from ble_hrm_freertos application. When NRF_LOG is enabled there is no way let the chip in low power consumption. I found...
Dear Technical Support,
I have faced a problem debugging firmware on our custom board based on Nrf52811. We use j-link EDU and Segger Embedded Studio as development tools...
Hello Nordicsemi community,
1) manual build of mcuboot - When trying to build the mcuboot for nrf5340 via the mcuboot/samples/zephyr via the west build command, the build...
HI , nrf52832 with SDK v16 on that using this nus example location below mentioned
examples\ble_peripheral\ble_app_uart\pca10040\s132
in this example, didn't change...
Hello,
I have recently received the nrf5340 development kit as part of the Hackster contest.
I followed the webinar and to get started
1. Connected board via micro USB...
I started a new ticket since I got a solution to not connecting to the cellular network. Apparently the iBasis sim is not working so I acquired a Hologram sim. I now can connect...
the code yesterday when debug can pop out voltage ,i do not chang anything today ,the code can not run the location ,i make three breakpoints in code and debug ,the code only...
First day using the new dev kit nRF52833-DK. Connected it up following the instructions on nordicsemi.com/start52833dk - computer won't mount the JLINK removable disk so I...
