Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Are there any nRF 52805 BLE examples anywhere on the net?
I have not been able to find any. Do they actually want to sell this chip? Do they like money?
Thanks!
Jam...
I am using nRF52810 with SDK 17.0.2 with UART function but I am getting error NRF_BREAKPOINT_COND. I also tried running the uart example of the SDK but the error still occurs...
Hello Nordic Team
I use SDK 15.3. I have an application that is based on ble_app_uart. It switches between uart and beacon advertisement periodically. I used pca10040_ble...
Dear Nordic Team,
i could not find a good and clean starting point for a development of a simple Open Thread application, which is not bases on CLI in the examples. Therefore...
Hi all,
I am now testing with ecdsa example with nrfutil generated key. I found that the public key generated by nrf_crypto_ecc_public_key_from_raw is not the same format...
Hi,
On new fresh delploy of cat Tracker web app, and asset tracker v2 aws without code change (i had a working version a week ago)
Now i have authentication error message...
Hello. I migrated my code from nRF5 SDK for Thread and Zigbee to nRF Connect SDK (NCS) . After that SPI code stopped working :( After debugging with the oscilloscope, I found...
Hi! I am trying to write code on MFRC522 to read data from RFID tags and write data to them, but the datasheet leaves much to be desired, and libraries are available only...
Hi,
I want to upgrate bootloader in my firmware.
IC: nRF52832
SDK: 17.02
I have finished my project, this project include boot + softdevice + app + settings,and...
Hello support team Devzone.
I am new member and i have a nRF51 DK board.
I try to create hex file for my nRF 51 DK board on the website : Mbed Compiler
when compiler...
Hello,
I'm sorry for this question, it can be easy for most of you I guess. I would like to measure the current consumption of the Thingy91, I see in the documentation...
I am running a simple cloud example where I am trying to send a CoAP GET message to coap.me:5683 server over Thread.
I can ping 64:ff9b::0808:0808 and get a response. I...
Hello I want to know what is the command that I must add to the ble_uart code which exists in the SDK library to send hello word using the bleutooth in the nrf UART application...
in \connect SDK\v1.5.0\nrf\samples\bluetooth\peripheral_uart,data number is limited 20 bytes, more than 20bytes BLE will part data in two or more packs to send or receive...
Hello everyone.
I'm trying to run examples provided in Zigbee v4.1 https://www.nordicsemi.com/-/media/Software-and-other-downloads/SDKs/nRF5-SDK-for-Thread/nRF5-SDK-for...
