Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Is it possible to （central side） send scan request fill the content based on received advertise information？
We want to control scan request message based on advertise content...
I am an experienced developer but struggling to understand nRF9160. Where can I find .h files defining HW? Where can I find data sheets describing peripherals? My task is...
Dear friend
Based on sdk17.0.2, in the ble_app_hrs routine, set NRF_SDH_BLE_SERVICE_CHANGED to 1, and by observing with nrf connect app, you can see that the Android phone...
If you take a 1K variable to a local variable, the AP will drop.
Static variables do not fall off.
I think it's a stack size issue, but how do I specify the stack size...
I am trying to get an nRF52811 to do extended advertising.
I am using: nRF5_SDK_17.0.2, version 7.2.0 of s140, SEGGER Embedded Studio 4.52, Windows 10
I have stripped...
I would like to confirm the update process when using nRF5SDK160098a08e2. I am aware of the following update process ----- Startup process: -MBR checks NRF_UICR->BOOTLOADERADDR...
Hello there,
I know how to measure the current based on Nordic tutorial. However, if I connected an external accelerometer by connecting Vdd and Gnd from nordic ev kit to...
Hi,
I want to run a CoAP server with Zephyr on a Thingy:91 over NB-IoT. Now I noticed that the Thingy only gets a private IPv4 address (10.x.x.x) from my provider which...
Hi, I am working on my custom made board, and I use P09 and P10 as digital outputs. I am aware I should disable NFC by adding the preprocessor: "CONFIG_NFCT_PINS_AS_GPIOS...
Hi All:
As the topic...........
1.what is the relations between the HID descriptor and data IN/OUT buffer?
2.Is the USB generic HID receiver_Function and tansmit_Function...
When launching the nRF9160, the following error occurred: <inf> at_host: UART check failed: 12. Dropping buffer and retrying.
Under what conditions does this come out? ...
I am trying to add DFU to my project, so I merged in the code from the example in the SDK as follows:
I included the same .c files as the example project
I copied over...
Hi,
I did some measurements today on our I2C bus and see that the GND level is different some times. The most time it is not GND level (about 800mV). I checked cross talk...
Dear
I increated a Generic Level module to main elements which have a Generic ONOFF module on Mesh example Light Switch Server project base on PCA10056 DK board for nrf52840...
