I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hello everyone. I work with nrf52840 chip and previously I had an app with softdevice (s140) and use BLE bootloader. Everything works as expected. Next I want to use another...
We are using ncs 2.6.0 and nrf5340 audio dks.
Sample is nrf5340_audio broadcaster.
One dk is configured to work as Audio Broadcast BIS Source and other as Sink. By default...
Hi there,
I am working on an audio recording and transfer application using nRF5340 (microcontroller development kit) and SPH0465 (digital microphone with I2S support...
Hello, I have designed my own board based on NRF52840-CKAA-R, which uses USB power supply. The working voltage of NRF52840 is 3.3V, and my test voltage is normal But NRF52840...
Hi,
I've ready many threads and docs on NRF52 SoC Revisions and Softdevice support but I am still confused. So apologies if I ask something which is already asked.
From...
Hi,
I want to implement low-power mode in my nRF5340 application. From what I understand, Zephyr's idle task automatically handles entering sleep modes, and the device wakes...
Hi,
I am evaluating warm and cold reboots, I am seeing no difference between them. I tried tracing sys_reboot definition, ended up with
For arm core with no handling...
As described in the docs.nordicsemi.com/.../powersave.html: “The application must choose the right duration based on the traffic pattern. Applications must also take appropriate...
Hi, I am using nrf9160 DK development board, i want to use gpio pins in this kit for a SPI interface from nrf52840, which pin i can use for this purpose. in datasheet it very...
Hello Nordic Team,
I am working on integrating the nRF21540 RF Front-End Module (FEM) with the nRF52840-QFAA in the 48-QFN package. Could you please provide the following...
Hi, I have reviewed the light_bulb app code in NCS2.8.0(include src code/CMakeLists.txt/prj.conf and so on)。 But I can't find where the path of matter is included, could you...
Hi all,
I wanted to enable read/write protection for MCUBOOT partition in my firmware from the application and encountered a strange problem. The build (build system - default...
Hi there,
This almost certainly has a simple answer but I can't work it out. I'm using the sample WIFI Scan for the above boards and can successfully scan away. But I'd...
Hi there, I am new to working with UART. I have managed to load the Nordic UART Service Client(Central) and UART Serial Port Emulation(Peripheral) without any sensors attached...
