Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hello,
i'm developing a board based on nrf5340 and i want to use npm1300 as the pmic. My board is very constrained in terms of space so i'm trying to trade-off the flexibility...
Hello,
Running on the latest 2v7 release 2 light switch examples, one running the lpn overlay and the other without. Creating a scenario with lpn node and a friendship node...
Hello all,
We are currently working with the nRF5340 on a custom board and have encountered an issue with the Real-Time Counter (RTC) using the nrfx libraries. The problem...
We have an application that is looking to receive a value of 'test\0' in a custom characteristic. From the Android version of nRF Connect, I just do this with a byte array...
I have a design in VS Code that works fine on a Windows 10 computer (original development was done here). Because I spend so much time waiting for my compute to compile my...
Hello, I want to know what voltage level are the pins on DK5340 , I am using USB cable for power supply. I read that the DK is compatible with ARDUINO REV3, so does that mean...
Hi, I am using nrf9160 with aws_iot library with zeyphros
Now the issue is when aws is initalized I get mpu fault, I have tracked down that issue is coming from mqtt helper...
It gives an error while updating with DFU. I am using the internal oscillator in the circuit. When I try it on a card with an external oscillator, the same DFU file works...
Hi!
I might be missing something obvious, but I'm having trouble reading the battery level at the Coiote LWM2M server connected to my Thingy 91.
The Thingy runs the asset...
Hello,
I am using the modem firmware 1.0.1 for DECT-NR+.
nrf_modem_dect_phy_modem_cfg in the latency field contains fixed delays in modem time units. Are those automatically...
I have been using an nRF52840 dev board and a nRF5340 dev board to program Bluetooth demos. Just today my nRF52840 board became very difficult to flash I get the error,
...
Bluetooth ips profile cannot access wan and can only communicate within the local area network. I am now using ubuntu as the router role of ipsp. Ubuntu has two network cards...
Hello,
We are currently implementing a custom DFU process for one of our client. They need to be able to upgrade the cores images, which are read from an SD-card. We already...
Hi everyone
We have had the experience on two different LwM2M servers that the Observer attributes are not being respected by the LwM2M client. Reading the Observer attributes...
He nordic expert:
Could we use CMW500's connection mode to test nRF52840's BLE RF? If nRF52840 support such connection RF test mode?
Following picture is CMW500's BLE...
