Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
I've got another question concerning a timeslot application.
In our timeslot application which is based on the nRF Mesh SDK timeslot.c implementation I noticed that if a...
I have a device using nRF52840 with SDK 15.2.0 and S140 6.0.0. It has failed with some kind of error. All core registers (including PC, LR) contain DEADBEEF. PRIMASK = 0xef...
I'm working on NCS 1.6.1.
I'd like to confirm if my method to get the RSSI is correct.
i test with a sample "peripheral_uart"
after BT connected, i printk the (NRF_RADIO...
I am testing the %XRFTEST Rx Test Command with the thingy91, with serial_lte_modem_2021-06-28_7a076c22.hex FW
and nRF Connect - LTE monitor software
I used the command...
The Repository link in the extension page on VS Code marketplace points to https://github.com/NordicPlayground/vscode-nrf-connect but that only returns 404 not found. I've...
Hello,
I am using the nordic nRF52840-DK and trying to connect to a nRF52840-Dongle and sending/receiving data to custom services and characteristics using pc_ble_driver_py...
Hi
I need to know, Is there any wifi module that supports for nrf5340 to communicate cloud or server??. If it is available kindly suggest us.
Thanks & Regards
Navin...
I am using Fanstel's BT840F BLE module which is based upon nRF52840 for my application. I am using PCA10056 DK to program it. I tried to program the BLE module on the DK with...
Hi,
We are using SDK13 and nrf52832.
I want to do multi pairing using Mode 1 Level 4.
Is there an example of multi-pairing and an example of deleting bonding individually...
I'm trying to update my devices from SDK 14.1 to SDK17. I've followed the pc-util instructions to create an SD+BOOT package, then after I'll send the updated application....
Hi,
I can use .overlay file to change the device tree setting of the nrf52840dk_nrf52840.dts.
However, my Board only has 1 button so I hope to "remove" 3 of the 4 buttons...
This discussion has been locked. I don't know why? and I don't know how to get it back.
devzone.nordicsemi.com/.../cannot-read-max30003wing-board-using-spi-communication...
I have an Zephyr application on the nRF5340 that I've been working on. I can debug fine in SES without a boot loader. However, when I add MCUBoot into the mix then everything...
I have some code that runs on the application and network processors that uses NRF_RPC NRF_RPC_CBOR (similar to the entropy_nrf53 sample) to communicate during boot loading...
I'm trying to get setup to debug an application that uses both the app and net cores. For now I'm using the example nrf/samples/nrf_rpc/entropy_nrf53/cpunet. I'm trying: ...
