Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Hi,
I am new to the nrf52 platform.
I am working on adding just works pairing and bonding to my BLE peripheral code. I tried to take reference from ble_app_bms example...
I have developed a data logger using nrf52832 s112 sdk 17.0.2 (nus service).It logs data upto 1mega Bytes,we have a custom buit android app with which we download the data...
Hello,
I am working on nRF52840 custom board, in that, I was facing issues with sd_softdevice_enable().
When I call the sd_softdevice_enable() it's stuck. Not return from...
Im using SPI interface to read data from https://docs.rs-online.com/7d34/0900766b81327f26.pdf using the D2 opcode.
The opcode starts reading the page from the flash (528...
Hi,
we are not able to see any output in NRF connect APP in FFBM mode with DTM Firmware,
However , on flashing complete firmware, we are able to turn on Beeper in FFBM...
Hello Nordic support,
I have a Zigbee coordinator application which has declared the time cluster as a server. I have a zigbee end device which has a time cluster as a client...
Hello I'm using nRF53 DK on zephyr v1.6.1. I'm now testing the power-saving mode. I tested the system-off example "v1.6.1/zephyr/samples/boards/nrf/system_off" and it works...
Hi,
I am using nrf52810 chip. we are trying multilink with central(1 central and two peripherals connected at a time),one central and one peripheral is fine, but we are...
Works on Huawei P20 Lite (Android v9), Samsung J3 (Android v7.1.1), all IOS phones. Doesn't work on Samsung A50.
Samsung A50 does see the devkit when using the same firmware...
OK, full disclosure - I'm pretty new to the whole nRF Connect/Nordic Semi environment, having had to jump across here after all the issues with silicon availability meant...
I would like to configure GPIOs as compatible = "nordic,nrf-gpio"; in devicetree file.
I did check this topic, but I think that this kind of configuration defeats the whole...
Hi, I'm working on a FreeRTOS (I just start to use it, so I'm a beginner) project in wish we want to use an external 32 MHz crystal. The program has a task that should be...
I want to implement CENTRAL using nRF52810. To implement the central, the softdevice must be s132 but I am not familiar with the softdevice concept. Until now, the softdevice...
Hello,
I closed below case by mistake.
nRF9160 receives garbage data on UART sometimes - Nordic Q&A - Nordic DevZone - Nordic DevZone (nordicsemi.com)
As per your...
