Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
I have seen this question asked a few times--but every thread seems to have no concrete answer.
I have uninstalled and reinstalled all JLINK drivers.
But still get the...
I am using the nRF9160 for IOT with the console connected on UART 0 there is a string of +CSCON: 1 and +CSCON: 0 messages displayed.
Build Zephyr 1.5.1
Modem firmware...
We're looking for some clear documentation for implementing OTA DFU via BLE on the iOS side. We have the firmware working well on our dev kits here, but working only with...
Hi,
Can you explain please why do you use all flash space for application (except SD area) in your examples. For example, SDK 17.0.0, HRS s132 example starts from 0x26000...
Hi
I have nRF SDK 17.0.2, and looking for ble_app_template application for PCA10100 to be flashed into nRF52833 DK. But seems that is not available.
Is there any other...
I'm developing a C implementation for nrfutil to make a Serial DFU in bootloader of sdk11. But I'm having an issue in serial communication. I've used a serial sniffer to compare...
I am using nRF52840 DK and connecting it with SPI to ESP32. The first bit of the transmission is missed for some reason. I could verify that the transmission is ok with logic...
Hi Nordic,
I'm working on a project using SDK 15.3, s140 , based on the LESC example for a central and peripheral application. I am able to bond with devices and later on...
Hi,
The MMD example published by the Nordic Team ( https://github.com/NordicPlayground/j-link-monitoring-mode-debugging ) is supposed to work with the nRF52DK (PCA10040...
Hi,
We have a custom board with nRF52840 based ISP1807 and developed the fw to some point. For some reason we tried to run the same fw on the nRF52840 DK rather our custom...
I'm trying to program an nRF52810 on a custom PCB using the nRF52-DK and am getting this error ((0x4) Lowlevel error: Unknown value (ffffff24)) when connecting with nRF Connect...
Hi there,
I'm working on something with hard real-time requirements - for this and a number of other reasons, I'm writing directly to the registers.
I'm trying to generate...
Hello,
Is it possible to multiplex coded phy and 1M for advertising and connections on zephyr? If so, do you have any available sample code or timing requirements?
...
I'm having a hard time wrapping my head around how to configure my LIS2DH accelerometer for 6D orientation detection with Zephyr. How would I manipulate the registers of my...
