Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
I have a bit of an odd one, and would appreciate any input. We have a fairly complex project, which does various things, but some of the time, I get a hardfault. The issue...
I am getting linker errors such as the following:
Output/Release/Obj/saadc_pca10056/nrf_sdh.o:SDK\components\softdevice\common/nrf_sdh.c:83: undefined reference to `start_sdh_req_observers...
Hello i have a keyboard with nrf52840 with ZMK firmware, BLE, adc, gpios, i2c0, usbd, DCDC and CONFIG_CLOCK_CONTROL_NRF_K32SRC_RC
When it is connected with the computer...
I would like to know the natural interrupt priority among different peripherals of nrf52840.
Specifically I am looking for default interrupt priority between RTC1 and TIMER1...
Hello, guys. I'm using the PCA10040 and the SDK 16.0's BLE UART peripheral example. I am trying to make PWM signal below.
When PWM0 stops, PWM2 works, and when PWM2 stops...
Hello everyone,
I am working on an nRF52-DK and getting familiar with Zephyr. In this process I am currently trying to extend the BLE MTU size beyond the default 23 bytes...
Hello,
My device is a USB HID peripheral connected to a PC. There is a case when the PC is turned off, but USB power is present. I want to detect this situation.
At the...
Is it possible to detect the presence of a Low Frequency Crystal and configure softdevice to use if present, otherwise use the internal RC oscillator?
A proposal would be...
Hi,
we have troubles to use 4wire NRF LPUART between nRF52840 (client) and nRF9160 Serial LTE Modem app (server).
We use v1.5.1 of nRF Connect SDK.
For nRF9160 we added...
Hello Team,
I want to know while Ble device is connected to the android device and within 5mins if device not get any data from android device then,
- Can device enter...
I am using sdk for mesh v.5 (s140.7.2.0) and nrf52840 DK and want to add uart peripheral into the client in the light switch mesh example and then trigger button 1 once a...
Hi,
I have written Hitachi AC IR transmitter using Smart remote 3 library.
Smart remote 3 library support 2 AC protocols, i.e., SIRC and NEC.
Kindly guide me how...
Hello, I essentially want to figure out a way to use the NFC buffer received by code like the writable_ndef_message example and have that same buffer, in the same code, advertise...
