I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Due to the recent semiconductor global shortage, we are changing the chip on our device currently on the market from the nRF52832 chip to the newer nRF52833. I am in charge...
RNG interrupt handler is not called.
Using nrfx_rng library to generate random numbers.
VALRDY event is generated but interrupt handler nrfx_rng_irq_handler in library...
I have looked at the UART example provided in the NRF52 SDK. The example uses the UART in blocking mode. I need to create a version that is non-blocking, and only reads the...
Hello Nordic,
I was looking at multiprotocol support from nRF Connect SDK by following this link: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/ug_multiprotocol_support...
Hi
Trying to install and operate the Sniffer based on nRF52840 USB Dongle
Having the nRF Connect for Desktop installed and burned the Dongle in accordance with the instructions...
Sorry I have to see how the ssp of ublox work.(nina 410)
II have to send a packet over the serial every 50mS.The packet len is 100byte.
I see that some time the received...
Hey DZ,
I'm having some trouble with the download_client. It's not playing nice with the HTTP server I'm using. On the last chunk of data, the nRF91 is issuing a Content...
Hello everybody.
I am developing a firmware which allows us to send data bidirectional between Central and Peripheral. On the one side we have a nrf51-DK and on the other...
Hi
I'm working on an application that utilizes CODED_PHY.
I'm working on top of ble_app_blinky examples (central and peripheral).
I've seen this post on DevZone:
https...
Hi forum,
I am working on nrf52832, using sdk 15.0.0. I am working on Ble_beacon using sdk sample code.
In the Sdk_config.h file default enable uart0. Why this need to...
I am trying to get the nRF BLE Sniffer v3.1.0 working on my Mac running Bg Sur using a nRF52840 dongle. I have followed all the instructions listed in the sniffer document...
mergehex does work with file paths with "..\" in them. Here's my folder structure:
project root
Firmware
Application
Bootloader
SDK_Libraries
nRF5_SDK_17_0_2 ...
We are using nrfSDK1702. We have been trying to lower the current from a beacon. The beacon is active every 10s, then go back to sleep. The current consumption stays around...
