Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hello, I have run into this problem again with regards to using the lwm2m_client sample. I can start running it fine but I get the error "Cannot init lwm2m engine" and "Cannot...
when compiling "ble_app_multirole_lesc_s140_pca10056" of sdk nRF5_SDK_17.0.2, crypto library not getting included, I am getting error, library is placed as shown in pic, also...
Hello,
I know that you can generate a single zip that contains dat and bin files for sd+bl and dat and bin files for the app.
Is it possible to generate a single dat and...
HI, I'm new here, hope following the rules for Questions.
I'm using nRF Connect v.3.6.1 and as toolchain SEGGER Embedded Studio for ARM (Segger edition) V5.34a.
I need...
Hello there,
I am using nRF52840 PDK and nRF5_SDK_for_Thread_and_Zigbee_v1.0.0 SDK for BLE and Thread development. I also have a BLE smartphone app communicating with nRF52840...
Hi,
-I have a custom board using nrf 52832 and I have interfaced LIS2DH12 using an SPI interface. -I am using SDK 15.2.0. -I am collecting raw data using FIFO mode and send...
I want to realize audio playing function in 9160, according to the specification, there are 9160 I2S interface. However, the specification only describe the definition of...
I am testing UART example using nrf52 DK(nrf52832), SDK17.0.2. (\examples\ble_peripheral\ble_app_uart\pca10040\s132) Setting UART initialization to a specific pin will halt...
I use ANCS example from SDK 15. But I found that I'm not able to get more than 32 chars for ATTRIBUTES (BLE_ANCS_ATTR_DATA_MAX). And it's a little short to get Title, Sub...
Hello,
in our application we have one central (nRF52840DK) and up to four peripherals (nRF52832). We want to achieve two goals in this application:
Goal 1: We need a synchronized...
Hello I have built a custom board using an nrf52810 chip and have been trying to upload some examples from the nrf52SDK (specifically BLE examples with the s112 SoftDevice...
Hi,
My nrf52840 dongle went to undefined state making all the leds on the board..Tried with different flavours of binaries but didnt got any luck the board remains in the...
Hi Supporter:
Hardware:nRF52840 dongle
Software: basic example "ble_app_interactive", s140_nrf52_6.1.1_softdevice
There is a strange problem,I connect my machine with...
Hi,
I've been trying to use a micro-USB cable to power the nRF52840 DK board but my Mac (Catalina version 10.15.6) isn't recognising the board in the system report, although...
