Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
On SDK16.0.0 + Mesh SDK 4.1.0
I've followed this to add PA/LNA support in the bootloader (Fanstel BT840X). I see the increase in RSSI and know that it is working.
...
Hi,
I am evaluating the Light Ctrl example of the Connect SDK 1.4.2. After nRF52840DK was programmed and provisioned by iPad, Mesh App, I was trying to bind application...
Hi,
I have built the example hrs_uart project and it works fine when I load the image into a pair of OCA10040 demo boards, one as application board and the other as connectivity...
Hi,
I am currently testing QSPI communication for flash. I am using the Termite console. When the console starting I got this error message:
uart:~$ [1B][8D[1B][J[00:00...
Hi,
I am trying to create a Mesh Network using CCT controlled lights and switch.
I want to fetch the present lightness value of the light(server) from the switch(client...
Hello,
I'm currently using SES for SW-development (NRF52). But especially for legacy code and refactoring I think this tool is absolutly not suitable (basic functions like...
Hi
We are using this combination of software:
Mesh SDK 4.2
Bluetooth SDK 17.0.1
Softdevice 7.0.1
Mesh DFU using the precompiled bootloader binary mesh_bootloader_gccarmemb_nrf52840_xxAA...
Dear sir,
Our code gets compiled using command emBuild.exe For programming NRF Connect Programmer tool is used.
I get following error while hex file is added to programmer...
HI All !
Hope you all are doing well !
I have a question regarding "Exporting Segger Embedded IDE Project/SDK to Arduino IDE or Vscode Studio" The Reason i want this is...
Due to some error, I lost 2 factor authentication key on my other account and cannot login from there. I want to recover that account or delete it. Please help.
There is no category for this problem. But the devzone has great information but a horrible user interface riddled with headaches.
1. Pet peeve #1: Trying to enter tags...
Hi,
I'm trying to evaluate the new Asset Tracker v2 example with a Thingy91, nRF cloud, and the supplied iBasis SIM, but when I build I get the following error:
C:/Nordic...
Hello,
in documentation of nRF9160 RSRQ is defined for 0..34 and 255.
What about values 35..254? Is it possible to get these values from the chip?
I have to know, if...
using any example with BLE I get the following:
when loading , prints on log :
[00:00:00.291,595] <wrn> bt_hci_core: ECC HCI commands not available
and when I...
Hello, Nordic.
I'm configuring a mesh network. The provisioner, client and server all going well, except for one problem.
I made a client and server based on sdk-coexist...
