Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
After programming the Ble_app_uart to the nrf52832, I am sending a 100 Bytes of data from my UART Port to Nordic chip and this data is transferred over BLE to my Phone. I...
According to Table 19 in the nRF24L01+ datasheet, writing to any of the 32 command registers is "Executable in power down or standby modes only". This caveat is also repeated...
Basically I want to get a 8 byte long MIC when using the AES CCM encryption. From the product specification it does seem like I can only get a 4 byte MIC, is that correct...
Hello,
I try to flash my dev card nrf52 with the program ble_app_uart
Or a program ble by cons I can flasher by other program (pin change in), I do not know from where the...
I created an characteristic that has MAX_Length = 20 Bytes characteristic.
And When I'm trying to write less than 20bytes on this Characteristic, It Always send with 20Bytes...
Is it OK to send multiple packet continuously over nus at below way without waiting for packet transmit complete?
i=UserUart.RxBuf[1]+2;
index = 0;
while(i>0)
{...
Hi,
I'm using nrf51822 Ek kit and running ble_app_uart example,when i want to send any character or integer it Received like a string only,but i want to send only single...
Hi,
this question is more about iOS than nRF, but there's probably here some experience around this subject.
First the context : We have a product based on nRF51, S110...
I compile a .bin file for DFU. The bin file is 62020 bytes. I create the zip file for DFU, it is 62909 bytes.
If I extract the zip file, I get the bin file (62020 bytes...
We are currently designing a prototype board for our product using the nRF52832. We need to calculate the transmission line with on a 4 layer PCB. The stack-up looks like...
I am trying to use your swift iOSDFULibrary cocoapod. What I am doing is the following. I have a library written in swift. That library is where I have your iOSDFULibrary...
As Bootloader IROM starting address 0x78000 and size 0x6000 is same in SDK 13.0 and 12.2.0 expecting to update Device firmware (BL+SD+APP) from 12.2.0 to 13.0.0 SDK.But in...
I use SDK9 nRF51.
I use white list. When I want to delete all bounded devices, I call this function. But it doesn't work. It not deleted.
Why I can't to delete bounded devices...
Hi,
I would like to know which is the difference between using a Softdevice or not.
Looking at the blinky example, the two versions are provided. The "main.c" file is...
