I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
I'm trying to setup an nRF52832 to drive 127 ws2812 by using PWM. It seems the bit-by-bit method is too slow for the 1.25uS period. pwm_set() is using somehow ~5ms, so that...
SDK : 2.6.1
uC: nrf5340
Hi,
how to avoid erasing of the application settings when updating the firmware via bluetooth.
When using the android version of "nrf connect...
I can program the spi and i2c find on my nrf54l15pdk board version 0.2.1, as soon as i turn on CONFIG_BT =y the device fails to do anything past being flashed successfully...
Hello,
I am looking to use the nRF9151 module.
I spoke with my wireless provider and asked what certifications they require to use their service. They said that they...
I am working on zigbee network
"In a Zigbee network, how can the coordinator retrieve the list of all devices connected to the network?"
What is the recommended way to...
Hello,
My team and I are working on a project where we need our nRF5340 to send data via UART from the board to a RaspberryPI. We designed a custom PCB with the chip and...
Hello,
We have devices in the field using NRF9160 V2 with NRF SDK 2.3.0 and MFW 1.3.4 on a Actinius Icarus V2 board. They are mostly working great, but sometimes some devices...
Hi, I am using nRF52840DK SDK 2.5.0 for testing Zigbee. I have three boards of this type, for the coordinator, router and end device.
For testing I use the end device I...
I am encountering the error <err> flash_nrf: invalid address: 0x00100ff8:8 when using NVS in my custom Zigbee project. However, the NVS functionality works properly in the...
I have a question regarding DFU while transitioning from development using the nRF52832 with the nRF5 SDK to the nRF5340 with NCS. Currently, I have a DFU app developed for...
I'm trying to install my dev environment on my MacBook. I've installed most of the tools but need the Segger installation to be properly licensed. I downloaded the Nordic...
Hello, After a lot of struggle i was finally made it to the point i can build and flash to my thingy 91 the lte_ble_gateway. However, i added prints (printk) in main.c to...
Im streaming audio from a gateway to headsets using BIS, but I am unable to get multiple streams working, so that I can switch between streams on the headsets. How do I set...
Dear,
We are using the nRF52840 with a proprietary protocol.
We plan to use the nRF52840 to sniff/poll RSSI on different (5/6) channels on periodic time (typ ~100 us)...
Hello, I have a problem on getting the dynamic tx power to work properly on the BL5340 using the hci_pwr_ctrl. I tried the example, it build and flash correctly, no error...
