I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
HI
when I try to uninstall/remove my connect sdk, tool chain manager says:
Failed to remove C:\nordicsemi\v2.6.0, operation not permitted. Please close any application...
Hi I have been working on an project using nrf5sdk_17_1_0 using Segger 5.42a but when I try to build the Blinky example it gives me build failed without any syntax error
We are developing a sleepy end device using the nRF52840, based on the light switch sample. We have set zb_set_ed_timeout to 16384 minutes, which is approximately 11 days...
Hello,
I am using the NRF52832 in my PCB design, and I have attached a screenshot of relevant part of the layout. My PCB manufacturer pointed out that some vias overlap...
Hello,
I have had this issue from the first time I installed VS Code and the nRF Connect Extension.
When I open my project, the connected devices pane is just missing...
Hi,
Since we started testing the new nRF9151 with the latest modem firmware (v2.0.1), we’ve noticed a change in GNSS behavior compared to the nRF9161/v1.3.6.
Recently...
Hi there!
We're trying to port the FreeRTOS Cellular Interface to work with the nRF9160 which is running the Serial LTE Modem application. The problem we are facing is a...
i have a nrf52840dk that is flashed with a old program i used. i want to try the nfc tag and read it using my phone. what should i flash to my nrf52840dk in order to use it...
Hello,
I am building the existing WIFI station app for the Thingy53 with the nRF 7002EB board - sample code: nrf/samples/wifi/sta
In the CMakeLists.txt file, the line...
Hi,
we are now using nRF Toolbox -> Logger tool on our phone to monitor Thingy91 application information via UART/BLE.
Now we would to monitor/log the same information...
Hi,
I am using NCS v2.4.2 and nRF5340DK + nRF21540EK but I can not enable GPIO+SPI mode.
for example, I use nrf/samples/bluetooth/central_and_peripheral_hr application...
I manage to connect to the network and disconnect from it after sending the data, but if I'm in an area without reception, the device tries to connect and after a while, the...
: Chip Not Recognized by J-Link
I need advice from someone familiar with the nRF9160-SICA-B1A-R7.
I purchased an nRF9160-SICA-B1A-R7 chip individually from Digi-Key and...
Dear Sir :
We are now developing on nrf52840, with ncs v2.6.1 and zephyr.
We want to put I2C0 to PM_DEVICE_ACTION_SUSPEND before sys_poweroff().
Our code is below :...
Hello everyone,
I am currently trying to get a ML model running on my nRF52 (preferred nRF52832 but nRF52DK works also for me). Right now I am trying to evaluate if my setup...
