Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I created xml file for heartrate server using bluetooth developer studio and the plugin nRF8001_Arduino (plugin nordic semiconductor for arduino)
the generated xml file...
I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
Hi,
We have developed firmware for a custom broad using the nRF52832 with 512kB flash, and our firmware currently uses 48.5% of the flash.
We are using Zephyr and version...
Above is the trace and the commands inserted. We were unable to get a response using the at+cops? command. Both SIM cards were active that we tested. We tested band 12. Could...
I would like to know more about the TLS 2K packet limitation in the nRF Connect SDK.
Is there a way to not be constrained by this limitation. I've seen some posts about...
Hi,
I am using nRF5340 DK and nRF SDK V.2.6.1 for my project
I am following the link;
https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate/lessons/lesson...
Hi,
I'm hoping you can help.
I am using the CENTRAL_UART and PERIPHERAL_UART to evaluate the nRF52840, and using a terminal program works fine.
What I want to do is...
Hi all,
I have a problem that seems very simple, but I cannot make sense of it.
I have a simple setup on the NRF52840 DK that senses a rising edge on pin 1.00 and...
I am trying to write tests for my code using CppUtest. I know the platform has memory leaks detection support. it seems that everyting is set up correctly to see the results...
Hello,
I am starting with the nRF Connect. I got a nRF52840 DK and I am following the 'nRF Connect for VS Code' YT series.
I got as far as part 5 (debugging), but I cannot...
Hi all,
SDK: NRF Connect v2.5.0 We've made a custom PCB with the NRF9160, and we have made a custom board configuration for it.
Our issue seems to appear when trying to...
Hello,
I have a mosquitto broker running on my pc. I want to connect and published to this broker through nrf9160.
The issue that I am facing is that prj.conf file only...
I want to use RTT log to output some data, but the data is output. 6 bytes in a line, but the first byte is an independent line, and the next 6 bytes are a line, staggered...
I would like to enable and configure the high power mode on the DC to DC converter in the nRF52840.
I am looking for the device tree source entries and the necessary entries...
Board: nrf7002 Project: matter_light_blub OS: Kubuntu 22 Toolchains: v2.6.1 SDK: v2.6.1
I am developing with the nrf7002, and my current setup involves using a Samsung A54...
Hello,
Is there examples of paring,bonding and whitelisting?
The pairing and bonding mode is static password.
It is best to have examples of the central and the peripheral...
