Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
I would like to emulate a NFC type 2 tag on a Nordic nrf52833 based device. I have the source code for the NFC driver (nrfx_nfct.c), but I can not find the source code for...
I would like to know if Nordic could provide me with a Zephyr compatible pre-compiled nfc_t2t library (nfc_t2t_lib_gcc.a or nfc_t2t_gcc_no_fpu.a). I managed to link library...
With SDK15.3 (it appears the issue exists in 17.1 as well), we are using the flash backend. To read the logs, we are doing the equivalent of flashlog_read_cmd(). This eventually...
Hi Everyone,
I recently purchased an nRF52840 DK (PCA10056, 2.0.1, 2021.7, 68365177) from mouser. Yesterday I successfully installed the nRF Connect for Desktop v3.9 application...
Hi there,
Does Nordic provide support directly for the Taiyo Yuden EKSKDNZWB Eval Kit and the EYSKDNZWB module? The Taiyo Yuden documentation seems to suggest that's the...
Hello,
I'm trying to see serial data (polling async method) coming from a single-wire signal. I have verified via an oscilloscope that there is indeed data on that wire...
Hello,
We are using nRFSDK v15.0.0 and nRF52840 in our system. There is also an external MCU that is connected to the nRF52840 via UART. Currently we are trying to perform...
Dear Members,
I want to use SDcard with softdevice, when I run fatfs_example()
I got this :
nfo> app: Initializing disk 0 (SDC)... rror> hardfault: HARD FAULT at...
Hello,
I've been working on a simple application to scan for bluetooth packets being emitted by another system, which advertises at a consistent 10Hz. We apply a filter...
Hi,
I try to do a OTA Update with watchdog enabled . The OTA Update runs and boots image B but this is stopped after watchdog timeout (1Sek). In my code the watchdog runs...
Hello all,
I am trying to develop an application where the user will input some specific commands i.e hex value of 0x01 via a mobile application and then via bluetooth this...
Hi,
I am migrating my code from sDK15 to SDK17. In SDK15 code app_timer_start() working fine with any timer value. But in SDK 17, I am getting error code 7.
When I debug...
Hai
I'm working on nrf52832 NFC, I have a few questions.
is NFC ID in nrf52832 is unique?
can I use it for payment purposes?
if that ID is not unique, any other solution...
Hello,
I am trying to use the **persistent** flash area of my nRF52.
I created a separate zone (PERSISTENT_FLASH) in my LD script as follows:
I try the following C...
