Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
When using SDK v13's I2S driver, the data to send is filled via data_handler callback. How do I fill last block data?
Assume i2s buffer size is 2000, then every 1000 words...
I have been going through the steps in this blog post: https://devzone.nordicsemi.com/nordic/cellular-iot-guides/b/getting-started-cellular/posts/getting-started-with-nrf9160...
Hello everybody,
I'll try to modify the ble uart example. The target is, to get data from two different nus Services (different characterisitv uuids). They are both initilised...
I basically need to use two UART instances with the BLE Buttonless DFU Template App.
I started using the Serial library but apparently it's no longer supported.
The methods...
Hello,
I am working on nRF52832 SDK 15.3.0 in segger studio.
In my project I have 2 ADC input pin.
ADC initialization is as shown below,
And every 0.5 second I read...
I have a custom BLE characteristic that I want to use to allow an app to send commands to my device. I use an on-write() function that is called whenever a BLE_GATTS_EVT_WRITE...
The Device's name UUID for Thingy52 in according to this site https://nordicsemiconductor.github.io/Nordic-Thingy52-FW/documentation/firmware_architecture.html is: EF68xxxx...
Hi I am using nrf52840 on a custom board with segger embedded studio as development IDE. I would like to flash the hex file generated without using segger embedded studio...
do you have a user gide for Serial DFU just like buttonless DFU ,like this link https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/getting-started-with-nordics...
Hi,
I have flashed lte_ble_gateway on nRf9160 DK (PCA10090) and hci_uart on nRF52840 SoC.
After flashing, I am getting some random RSSI values and MAC Address , instead...
Hello,
I have two micro-controllers communicating over SPI.
The STM32F746 is SPI master. The nRF52840 is SPI slave. I use SDK v15.3.
I am sending two bytes over SPI...
Hi.
I had to unpair from the Android Bluetooth list by doing pm_peers_delete () when bonding. It's ok. I know why it should. But sometimes I can't find my paired device...
To the kind attention of Nordic support team,
We are very interested indeed in using your nRF52840 and nRF52810 devices in our projects. We also would like to use your gazell...
Hi,
I have used nRF52832 with my Python code succesfully many days. Suddenly it stopped to working and gives me an error message: NordicSemiException: Failed to ble_gap_scan_start...
