I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi ...
how to send the particular message from client to specific server in mesh ? i am using mesh 3.1 version
i want to use 4 server and one client . client have to send...
Hi
We use the function "sd_ble_gatts_value_set()" for setting new values of a characteristic(not changing the length). This function takes between 120 and 260 us time to...
Hey,
I was wondering if I can write C++ code for the NRF9160:
Does the NRF9160 DK support C++?
Is SEGGER IDE compatible with it?
Is it recommended to use C++ in...
Hi:
I use the SDK 13.0 and nRF52 DK to develop software for the project. Based on BLE UART (NUS), the software do SAADC sample and transfer the data out in real time, The...
I have recently ported our working project to SES. The project uses S140 with nordik SDK 15.20 on nRF52840 custom board. the project also makes use of freeRTOS. It's important...
Hello,
mqtt_simple was probably never tested in TLS because some parts for TLS are missing (see client_init)
Could you make a good exemple that works please ?
hi...
I am working with thingy52 while compiling i am getting this error , then i moved to segger , in segger i am getting following errors
how to overcome this ? help...
Hello -
We are interested in using NimBLE for a nRF52 project as we've used NimBLE on another micro controller. NimBLE would be running on FreeRTOS and we are developing...
Hello everyone,
I'm trying to generate a periodical sine signal at the output of a 10 bit DAC without CPU interaction. The DAC uses an SPI interface, thus my idea was to...
I am trying to run adafruit_tag_reader example on nRF52840 DK .
Problem :
If these are my pins in sdk_config.h it works fine
Whereas this doesn't work.
nrf52832 softdevice S132 SDK15 custom board
TWI instance
TX(nrf_drv_twi_tx) failed, slave device is AD5252 digital potentiometer, i want to send data to the potentiometer...
Hi Sir,
I want to sent specific message to a defined server with a static ip configured. Kindly let me how we can do this in nRF9160 with NBIOT network.
Regards, ...
Hello,
we starting the production of first lot our devices on NRF52840CKAA (WLCSP).
We get some issues with manufacturing, which can be separated into to 2 parts:
...
