Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
nrfConnect for MacOS won't allow pairing of a BLE peripheral with a nrf51 based dongle.
nrfConnect Version 2.4.0.
dongle PCA 10031 V1.1.0
Mac OS version 10.11.6
A...
Hello, so I have a central and two peripheral cards that each send their counters to the central. What I want to do is compare each of the two counters. But there's a problem...
Can I use the ble_advertising module for the BLE_GAP_PHY_CODED ? Currently my Coded PHY parameters without the module are defined as:
Following the example at NordicPlayground...
Hi all,
I am working on an application where I have an application MCU and my idea was to use nRF52 as a 'modem' over serial API. The device I am making is supposed to be...
When nrf52 board and tablet PC connect, I set the tablet PC in sleep mode. Then how can I wake up tablet PC via pushing a button on nrf52 board. Maybe one event can realize...
Include other files in the ZIP file. Is it possible to include files that are not related to updating in the ZIP file of firmware update? I want to pass the configuration...
Hi all ,
I using sdk12.3 experimental_ble_app_buttonless_dfu project to development , below is my bootloader and project ram setting:
if I don't download the bootloader...
sdk12.3.0 In the ble_app_hrs_rscs_relay example, I added the uart_init function referring to the ble_uart example, but when I execute the APP_UART_FIFO_INIT () function, a...
My development environment is PCA10028, SoftDevice 130, SDK12.3.0
Two nRF51822s were mounted in one board One nRF51822 will be used as a TWI master and the other as a TWI...
It is said that ble5.0 can cover a range of 300m, I wonder how big is current when this is achieved? For 52840, the largest power output is 8dBm, for 52832, the largest output...
Hi,everybody!
I use nRF52832,supply volt 3.0V normal, program can be downloaded , run and debug,i ensure the program is accurately.To control a gpio P0.09,on the hardware...
Dear Nordic,
I debug the SDK15 example project ble_app_template_pac10056_s140 project, nothing change, but it will jump into app_error_weak.c as below picture, please help...
I can not get information about the power consumption when twi is enabled and idle. It just state the current when it is running. So do I need to disble it when it is idle...
Greetings,
We have taken the RAM Retention example and are experiencing a failure (all LEDs on) when setting MAX_TEST_ITERATIONS to a value greater than 1. This is duplicated...
