Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
I am developing one project where I use the Rigado BMD-300 Series Evaluation Kit for controlling one ws2812b strip with 8 LED.
Currently, the system work as I intend when...
We are developing our product on nRf52832QFAAB0 SoC. BLE 4.2 is currently implemented in our products.
Seeing all features in BLE5 (long range, Higher throughput, increase...
Hi,
Why doesn't Nordic offer a stand-alone BLE controller variant of its softdevice protocol stack? As far as I understand, the softdevices includes both Host and Controller...
hi,
I am using nRF52-DK with nrf Sniffer
What are LED 1 and LED 2 Indicate ?
Initially LED 2 Blinks very Fast, Sometimes LED 1 is Off LED 2 is ON
sometimes LED 1 and...
When and where can we purchase the nRF52840 chip for engineering developpement and production in China, and how long is Manufacturer Lead Time? Thank you.
I am using nRF Connect app testing bluetooth connection ,and I got problems in some Moto phones ,and error message is in the below pictures , below model number is Moto Z...
Hello,
I'm currently migrating from SDK13.1 to 15.0. I'm doing it in steps so I first started migrating to SDK14.2. After I finally got rid of all the warnings and errors...
I am using nRF52832 pca10040 developement board. As I am begineer I dont know much about coding. I am using Eclipse IDE for developement. I want to transmit 1-10 numbers using...
BLE_GAP_ADV_SET_DATA_SIZE_MAX is use din ble_advertising.h
This macro is defined in ble_gap.h for each softdevice - however not in the header for S332. Also ble_gap_adv_data_t...
Is race condition possible when stopping advertising?
I need to disable BLE for some time to perform critical tasks. I need to stop advertising and be disconnected.
Let...
Hi Nordic team
As the title mention, I would like to program the DTM and radio test mode on thingy.
Did thingy support it?
Can I flash both program in thingy and switch...
Hi.
I scan devices with sd_ble_gap_scan_start command and on start it consumes around 6mA.
here are my parameters:
#define SCAN_INTERVAL 0x00A0 /**< Determines scan...
Hi,
For some reason when i do "project -> clean target" Keil deletes the softdevice Hex file in addition to the project compiled files.
Is that the normal behavior?...
