HI,
I am using the nrf_desktop sample in NCS V3.0.2, I want to buil with prj_release_dongle.conf , the setting
but build fail, I check the file Path: it should be F...
Hi:
PLEASE CANCEL THIS TICKET
I'm doing exercise 1 of lesson 1 of the nRF Connect SDK Intermediate course. It says: Get the source code of this course as a third-party...
I am using the NRF Connect SDK package provided by Qorvo, and adding BLE functions to their package. I am now trying to debug my added code.
I am using Ozone as the debugger...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I have several deployed devices that have been running for a while, using the nRF Cloud A-GNSS system with the nRF Location library. These devices were successfully...
hi I have recently been developing ncs on vs code. However, I encountered a strange problem. After I clicked build configuration, there was no output in the terminal, except...
Hello all,
I have this problem: when I add support for OTA my bonding information are canceled after power on. Without ota all is perfect.
Example: - Turn on the device;...
Hey there!
I am currently trying to upload a .hex file onto the board to flash it using the nRF connect programmer. But while flashing i get this error:
11:10:10.496...
Hello,
I am currently working on the Exercise 3 – Interfacing with ADC using nrfx drivers and TIMER/PPI sample. I have it operating, however I am wondering what is the proper...
Using NCS 2.6.2
set(PM_STATIC_YML_FILE ${CMAKE_CURRENT_SOURCE_DIR}/configuration/pm_static.yml) in the CMakeLists.txt works well to use static partitions for a appl+mcuboot...
Hi
I have been using the nrf52840 development kit. In the sdk examples I am running the radio test example of pca10056, but in the retarget.c file I am getting this error...
Hi,
I'm working on a testbench to flash product with nRF5340 and nRF52840 chips.
In order to erase/flash both I'm using JLink Base compact and nrfutils CLI. But I have...
I've been trying to build the BLE Audio Broadcast source to run on my nRF5340 Audio DKs using the line in as the audio source. I've been developing on nRF52 for a while using...
Hi!
I need to create an application that sends text messages to a private server, such as ptsv3.com.
Could somebody please help me make this application work?
I encountered...
Dear Community,
I am currently working on an LTE-M and NB-IoT project in India using the nRF9151DK and testing the AWS IoT sample. Everything is set up, except for an active...
Hi, We are using following HW and peripherals: - nRF52840 - I2C - ADC - RTC1 - RTC2 - PWM - GPIO - SWI. We are using following 3rd party libraries: - nRF5 SDK v17.1.0 - FreeRTOS...
Hey All, I am sorry if this question may seem absurd or very very illogical, I am not very good at hardware but here I go. So I am designing a circuit around nRF54L15 as my...
